Hotpoint LSTB 6M19, Operating Instructions Manual

GB

5

Technical data

Dimensions

width 45 cm

height 85 cm

depth 60 cm

Capacity

10

 standard place-settings

Water supply pressure

0,05 ÷ 1MPa (0.5 ÷ 10 bar)

7,25 – 145 psi

Power supply voltage

See appliance data plate

Total absorbed power

See appliance data plate

Fuse

See appliance data plate

This dishwasher conforms to the 

following European Community 

Directives: 

-2006/95/EC  (Low Voltage)

-2004/108/EC (Electromagnetic 

Compatibility) 

-2009/125/EC (Comm. Reg. 

1016/2010) (Ecodesign)

-97/17/EC (Labelling)

-2012/19/EU

Waste Electrical 

and Electronic Equipment 

(WEEE)

*

Only available in selected models.

the plug (

see Repairs and After Sales)

. Do not use extension 

cables 

or multiple sockets.

Once the appliance has been installed, the power supply 

cable and the electrical socket should be easily accessible.

The cable should not be bent or compressed.

If the power supply cable is damaged, have it replaced by 

the manufacturer or its authorised Technical Assistance Service 
in order to prevent all potential hazards. 

(See Repairs and After 

Sales)

The Company shall not be held responsible for any incidents, 

if these regulations are not observed. 

This appliance must be earthed.

Fuses:your appliance comes fitted with a plug and a 13A fuse. If 
you need to replace the fuse, only those rated at 13A and ASTA 
approved to BS1362 should be used. If you lose the fuse cover, a 
replacement may be obtained from your local authorised Service 
Centre or Electrical company. Correct replacement is identified 
by colour coding or the marking on base of plug.
DO NOT use the plug unless the fuse cover is fitted.

Changing the Plug

Cut off and dispose of the supplied plug if it does not fit your 

socket.

To avoid a shock hazard DO NOT insert the discarded plug 
into a socket anywhere else.

Wires in the mains lead are coloured accordance with the 

following code:

Green/Yellow      - 

Earth

Blue 

  - 

Neutral

Brown   

  - 

Live

If you change the plug, the colour of the wires in the mains lead 
may not correspond with the terminal markings in the plug, which 
if not coloured, could be:

EARTH  ‘E’   or  
NEUTRAL 

‘N’

LIVE 

‘L’ 

Changing the Mains Lead

A lead can be ordered from Hotpoint Service:

- If you have damaged the existing lead or require a longer one 
a charge will be made.  It is strongly advised that this work is 
carried out by a qualified electrician.
- If the domestic wiring includes a residual current-operated 
circuit breaker, ensure that it conforms to the latest regulations.

 The dishwasher must not be connected to the electricity supply 
while installation is being carried out.
- This appliance should only be connected to a 230/240V AC 
source, via a properly installed earthed socket.
- Use the dishwasher solely in a domestic environment.
- DO NOT stand or place heavy objects on the door when it is 
open, this could damage the door or cause the appliance to tip 
forward.

Advice regarding the first wash cycle

After the installation, remove the stoppers from the racks and the 
retaining elastic elements from the upper rack

 (if any).

Water softener settings

Before starting the first wash cycle, set the hardness level of 
the water from the mains supply. 

(see  chapter  Rinse  aid  and 

refined salt).

First load the softener tank with water, then introduce about 1 kg 
of salt. It is perfectly normal for water to flow out.
As soon as this procedure is complete, run a wash cycle.
Only use salt that has been specifically designed for dishwash-
ers.
After the salt has been poured into the machine, the LOW SALT 
indicator light

* 

switches off.

If the salt container is not filled, the water softener and the 

heating element may be damaged as a result.

The machine has a buzzer/set of tones 

(depending  on  the 

dishwasher model

)

 to inform the user that a command has 

been implemented: power on, cycle end etc. 
The symbols/indicator lights/LEDs on the control panel/
display may vary in colour and may have a flashing or fixed 
light 

(depending on the dishwasher model)

.

The display provides useful information concerning the type 
of wash cycle, drying/wash-cycle phase, remaining time, 
temperature etc etc.