background image

Page 1

•  Do not operate the main audio/video button controls on any external 

media devices such as a CD or DVD player while inside in the spa.  

Operation of integrated audio/video equipment through the spa 

control panel or wireless remote is permitted and acceptable.

•  Do not connect any auxiliary components (for example, cable 

additional speakers, headphones, additional audio components) to 

the audio system unless approved by 

Watkins Wellness

 . 

•  Do not self service audio component by opening spa door as this may 

expose dangerous voltage or other risk of injury. Refer all servicing to 

qualified service personnel.

•  Do not attach an external antennae to a spa audio system unless 

installed by a licensed electrician in accordance with National Electric 

Code.

WARNING

•  To reduce the risk of electrical shock, replace a damaged cord 

immediately. Failure to do so may result in death or serious personal 

injury due to electrocution.

•  In order to avoid a hazard due to inadvertent resetting of the thermal 

cut-out, this appliance must not be supplied through an external 

switching device, such as a timer, or connected to a circuit that is 

regularly switched on and off by the utility. n order to avoid a hazard 

due to inadvertent resetting of the thermal cut-out, this appliance must 

not be supplied through an external switching device, such as a timer, 

or connected to a circuit that is regularly switched on and off by the 

utility. 

•  Your spa must be supplied by a ground fault circuit interrupter - 

residual current device (RCD) - with a tripping rating not exceeding 

30 mA in an electrical subpanel. Always test the Ground Fault Circuit 

Interrupter (GFCI) before each use of the spa. If the GFCI does not 

perform properly, a ground current is flowing indication the possibility 

of electric shock. Disconnect power to the spa until the fault has been 

identified and corrected.

NOTE: 

Failure to wait 30 seconds before resetting the GFCI may 

cause the spa’s Power Indicator (on the control panel) to blink. If this 

occurs, repeat the GFCI test procedure.

•  Install the spa so proper drainage is provided for the compartment 

containing the electrical components.

DANGER - RISK OF ELECTRICAL SHOCK

•  Install at least 1.5 m (5 feet) from all metal surfaces. A spa may 

be installed within 1.5 m (5 feet) of a metal surface if each metal 

surface is permanently connected by a minimum 6mm² solid copper 

conductor attached to the wire ground connector on the terminal box 

that is provided.

•  Do not permit any external non spa integrated electrical appliances, 

such as a light, telephone, radio, or television within (1.5 m) 5 feet 

of a spa. Failure to maintain a safe distance may result in death, or 

serious personal injury due to electrocution, if the appliance should fall 

into the spa.

•  Do not permit any electrical appliances, such as a light, telephone, 

radio, or television within 1.5 m (5 feet) of a spa. Failure to maintain 

a safe distance may result in death, or serious personal injury due to 

electrocution, if the appliance should fall into the spa.

Safety Information

Safety Information

IMPORTANT SAFETY 

INSTRUCTIONS

(READ AND FOLLOW ALL 

INSTRUCTIONS)

AVOIDING THE RISK TO CHILDREN

DANGER - RISK OF CHILD DROWNING

Extreme caution must be exercised to prevent unauthorized access 

by children.  To avoid accidents, ensure that children cannot use a spa 

unless they are supervised at all times.

WARNING

To reduce the risk of injury, do not permit children to use this spa unless 

they are closely supervised at all times.
•  To reduce the risk of injury, lower water temperatures are 

recommended for young children. Children are especially sensitive to 

hot water.

•  The device should not be used by persons (including children) with 

reduced physical, sensory or metal capabilities, or lack of experience 

and knowledge, unless they receive supervision or training.

DO:

•  Make sure you always lock the child resistant locks after using the 

spa for your children’s safety. Every 

HOT SPRING

 spa is equipped 

with a locking cover that meets the ASTM F1346-91 Standard for 

Safety Covers.

•  Test the water temperature with your hand before allowing children to 

enter the spa to be sure that it’s comfortable. Children are especially 

sensitive to hot water.

•  Remind children that wet surfaces can be very slippery. Make sure 

that children are careful when entering or exiting the spa.

DON'T:

•  Allow children to climb onto the spa cover.
•  Allow children to have unsupervised access to the spa.

AVOIDING THE RISK OF 

ELECTROCUTION

DANGER - RISK OF ELECTROCUTION

•  Connect only to a grounded source.
•  Do not bury the power cord. A buried power cord may result in death, 

or serious personal injury due to electrocution if direct burial-type 

cable is not used, or if improper digging occurs.

•  A ground terminal (pressure wire connector) is provided on the control 

box inside the unit to permit connection of a minimum 6 mm

² (

No. 10 

AWG) solid copper bonding conductor between this point and any 

metal equipment, metal water pipe, metal enclosures of electrical 

equipment, or conduit within 1.5 m (5 feet) of the unit as needed to 

comply with local requirements.

Summary of Contents for Aria ARE

















































Reviews: