HotSpring HOT SPOT Pace, Owner'S Manual

FILTER CYCLES

When the spa is first powered up, the automatic filter cycle will wait 

10 minutes before starting. Your spa will automatically turn the first 

filter cycle on for 60 minutes on low speed. The second filter cycle will 

activate for 30 minutes, 12 hours later. The filter cycle icon, F1 or F2 will 

be displayed in the control panel during the filter cycle. 

NOTE:

 When using @ease SmartChlor, the initial recommended 

minimum filter cycle setting is 2 hours 30 minutes, twice a day (5 hours 

total). You may adjust this setting based on your bather load.

NOTE: 

The optional 

FRESHWATER

III ozone system only works during 

the filter cycle.
To modify the length of either filter cycle:
A.  Press the MODE (



 or 



) button until the 

TOOLS menu is displayed.

B.  Press the 

(+)

button to enter the TOOLS 

submenus.

C.  Press the MODE (



 or 



) button until 

FILT1 or FILT2 is displayed.

D.  Press the 

(+)

button to enter FILT1 or 

FILT2. F1 or F2 icon will flash.

E.  Using the 

(+)

 or the 

(-)

 button, adjust the 

desired filter cycle time, from 0 to 6 hours.

F.  Press the MODE (



) button in FILT1 to go 

to the RESET screen. Press the 

(+) 

button 

if you want to reset the filter 1 starting time 

to the current time or press the MODE (



) 

button to go the the EXIT screen. Press the 

(+) 

button in the EXIT screen to go to the FILT2 screen.

The filter cycle will activate the jet pump on low speed for the entire 

cycle. When activated, the filter cycle icon on the display is turned on. 

If the temperature exceeds the set point by three degrees F for more 

than three hours, the system will cancel the filter cycle for the remaining 

filter cycle time. Should the temperature cool down to 1.5 degrees F (1 

degree C) below the set point before the end of the cycle, the cycle will 

resume for the rest of the time. Should you use the spa during the filter 

cycle by placing the jet pump on high speed, the Filter icon and Jets icon 

will be on. Once the jet pump has been shut off, a ten minute tranquil 

mode begins (Filter & Jet icons are off during tranquil mode while F1 

or F2 remain lit). The Filter and Jet icons will come back on once the 

tranquil mode ends if the filter cycle timer is still on.

BRIGHTNESS - LCD

If you would like to change the brightness of the Control Panel screen:
A.  Press the MODE (



 or 



) button until the TOOLS menu is 

displayed.

B.  Press the 

(+)

button to enter the TOOLS 

submenus.

C.  Press the MODE (



 or 



) button until 

LCD is displayed.

D.  Press the 

(+)

button to enter into the LCD menu.

E.  Using the 

(+)

 or the 

(-)

 button, adjust the desired screen brightness.

AUDIO MENU (OPTIONAL)

The following applies to spas that have an optional wireless audio 

system installed: 
When the wireless audio system has been installed on the spa, the 

control panel can be used to control the audio system. The following 

information demonstrates how to navigate the music menu by using the 

spa’s control panel.

AUDIO MENU

An AUDIO menu will be accessible on the 

control panel screen. 

To access the menu, press the MODE (



 or 



) button until AUDIO is displayed.

BASIC CONTROL PANEL OPERATION

1.  To enter into a sub-menu press the 

(+)

button.

2.  To move to the next menu press the MODE (



) button

3.  To exit from any sub-menu, press MODE (



 or 



) button as many 

times as necessary until EXIT is displayed then press the 

(+)

button 

to exit that sub-menu.

TO TURN AUDIO SYSTEM ON/OFF 

(OPTIONAL)

From the AUDIO screen:
1.  Press the 

(+)

button to display POWR -.

2.  Press the 

(+)

button to display POWR + 

and turn the audio system ON. Press the 

(-)

button to  

display PWR - and turn the audio system OFF.

IMPORTANT: 

The power can take a few seconds to turn on or off.

TO PAIR BLUETOOTH

On your device, find 

My Spa BTXR

. If you DO NOT see this, another 

device may already be connected (see To Disconnect Bluetooth on 

following page).
1.  Press the MODE (



 or 



) button until the SETUP screen is 

displayed.

2.  Press the 

(+)

button to display one of three audio sources, BLUE,TV, 

AUX in the setup menu. Bluetooth should be selected.

3.  Press the MODE (



 or 



) button until the PAIR+ screen is 

displayed.

4.  Press the 

(+)

button followed by pressing "connect" next to 

My Spa 

BTXR

 on your device to pair.

After pairing, you will be ready to use your Bluetooth device. Only one 

paired Bluetooth device will work at a time.

TO ADJUST VOLUME

From the AUDIO screen:
1.  Press the 

(+)

button to display POWR.

2.  Press the MODE (



) button to display 

VOL.

3.  Press the 

(+)

button to increase volume and the 

(-)

button to 

decrease volume.

NOTE:

 Volume range is from 0-40. No number displayed indicates 

Volume is OFF.

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

POWER

Operating Instructions

Page 16

Operating Instructions