Page 18
To decrease the set temperature, press the
(-)
button, once for each degree of decreased temperature desired. If you hold the
(-)
button down, the set
temperature will decrease by one degree every half second.
JET PUMP CONTROL
Pressing the
JET
button for the
TEMPO
,
RELAY
&
RHYTHM
changes the jet pump functions, depending on the number of presses:
1st press:
Two-speed jet pump runs on low speed
2nd press:
Two-speed jet pump runs on high speed
3rd press:
One and Two-speed jet pumps run on high speed
4th press:
One-speed jet pump runs on high speed
5th press:
Both jet pumps are off
LIGHT - ON/OFF & INTENSITY CONTROLS
The light control uses four positions: High, Medium, Low, and Off. To turn on the spa light, press the LIGHT button. This will place all lights in the
spa in the High, or maximum intensity position. When the lights turn on, the light symbol will also illuminate on the control panel display. Press
the LIGHT button again to lower the intensity of the lights to the Medium position. Press the LIGHT button again to lower the intensity even more,
placing the lights intensity in the Low position. Press the LIGHT button one more time to shut the lights off. When the lights are deactivated, the light
symbol will also turn off.
If the lights are left on, they will automatically be turned off by the control system after 6 hours of continuous operation. The light symbol on the
panel will also turn off when the lights are deactivated.
If the lights will not turn on, make sure SPA LOCK is deactivated. SPA LOCK disables all the controls on the control panel (see following pages for
more information on SPA LOCK).
SYSTEM MODE
Your spa is equipped with a System Mode. This function will allow you to conveniently turn the jet(s) on high speed and the lights on maximum
intensity at the same time.
To activate the System Mode, perform the following functions:
Press the MODE (
or
) button until SYSON is displayed on the screen. Press the
(+)
button to activate the SYSON mode feature. The jets and
light icons will remain illuminated on the display until the system mode is deactivated.
NOTE:
Once activated, the jet and light functions can still be changed by pressing the JETS or LIGHT button.
To deactivate the System Mode, press the MODE (
or
) button until the SYSON symbol is displayed on the screen.
Press the
(-)
button to deactivate.
CLEANING MODE
All spas are equipped with a “Cleaning” mode. When the mode is activated, the jet pump in the first jet system will turn on and run for ten minutes
(used for water maintenance). To activate the “Cleaning" mode, press the MODE (
or
) button several times until the CLEAN menu is
displayed. Press the
(+)
button to activate the CLEAN mode feature.
NOTE:
The jet icon will flash on and off while the “Cleaning ” mode is active.
To stop the Cleaning Cycle before the ten minutes is complete, Press the MODE (
or
) button several times until
the CLEAN menu is displayed on the screen then press the
(-)
button to deactivate.
NOTE:
Pressing the JETS button will also deactivate the clean cycle and the jet icon will remain on and solid
TOOLS MENU
The TOOLS menu is one of the main menus on the control panel. Within the TOOLS menu are seven submenus, which consists of; Temp Lock,
Spa Lock, Light, Econ or Summer Timer, Filter 1, Filter 2, LCD and Exit.
To enter onto the TOOLS menu, scroll through the main menus using the MODE (
or
) button until TOOLS is displayed. Press the
(+)
button
to enter into the TOOLS submenu, use the MODE (
or
) button to scroll through the submenus. Once the desired submenu is displayed, press
the
(+)
button to activate that submenu. To leave the TOOLS submenu, scroll through the submenu using the MODE (
or
) button until EXIT is
displayed, then press the
(+)
button to exit the submenu.
LOCKING FEATURES
The two locking features, SPA LOCK and TEMPERATURE LOCK, are enabled from the control panel by pressing the MODE (
or
) button until
TOOLS is displayed. Then press the
(+)
button to enter the TOOLS submenus. Use the MODE (
or
) button to scroll through the submenus to
get to the locking features. Once enabled, a lock will remain active until the specific button combination is applied to disable the lock. Even if power is
disconnected from the spa and soon thereafter reapplied (such as in a power outage) the lock will remain in place.
SET
READY
F1
F2
READY
READY
READY
READY
READY
READY
READY
F1
READY
F1
F2
SET
F1
F2
SET
READY
F1
F2
READY
POWER
POWER
POWER
POWER
POWER
POWER
POWER
READY
F1
F2
POWER
Page 18
Operating Instructions