Page 20
FILTER CYCLES
When the spa is first powered up, the automatic filter cycle will wait 10 minutes before starting. Your spa will automatically turn the first filter cycle
on for 60 minutes on low speed. The second filter cycle will activate for 30 minutes, 12 hours later. The filter cycle icon, F1 or F2 will be displayed in
the control panel during the filter cycle.
NOTE:
The optional
FRESHWATER
III ozone system only works during the filter cycle.
To modify the length of either filter cycle:
A. Press the MODE (
or
) button until the TOOLS menu is displayed.
B. Press the
(+)
button to enter the TOOLS submenus.
C. Press the MODE (
or
) button until FILT1 or FILT2 is displayed.
D. Press the
(+)
button to enter FILT1 or FILT2. F1 or F2 icon will flash.
E. Using the
(+)
or the
(-)
button, adjust the desired filter cycle time, from 0 to 6 hours.
The filter cycle will activate the jet pump on low speed for the entire cycle. When activated, the filter cycle icon on the
display is turned on. If the temperature exceeds the set point by three degrees F for more than three hours, the system will cancel the filter cycle for
the remaining filter cycle time. Should the temperature cool down to 1.5 degrees F (1 degree C) below the set point before the end of the cycle, the
cycle will resume for the rest of the time. Should you use the spa during the filter cycle by placing the jet pump on high speed, the Filter icon and
Jets icon will be on. Once the jet pump has been shut off, a ten minute tranquil mode begins (Filter & Jet icons are off during tranquil mode while
F1 or F2 remain lit). The Filter and Jet icons will come back on once the tranquil mode ends if the filter cycle timer is still on.
BRIGHTNESS - LCD
If you would like to change the brightness of the Control Panel screen:
A. Press the MODE (
or
) button until the TOOLS menu is displayed.
B. Press the
(+)
button to enter the TOOLS submenus.
C. Press the MODE (
or
) button until LCD is displayed.
D. Press the
(+)
button to enter into the LCD menu.
E. Using the
(+)
or the
(-)
button, adjust the desired screen brightness.
AUDIO MENU (OPTIONAL)
The following applies to spas that have an optional wireless audio system installed:
When the wireless audio system has been installed on the spa, the control panel can be used to control the audio system. The following
information demonstrates how to navigate the music menu by using the spa’s control panel.
AUDIO MENU
Once the music system is installed, an AUDIO menu will be accessible on the control panel screen.
To access the menu, press the MODE (
or
) button until AUDIO is displayed.
BASIC CONTROL PANEL OPERATION
• To enter into a sub-menu press the
(+)
button.
• To move to the next menu press the MODE (
) button
• To exit from any sub-menu, press MODE (
or
) button as many times as necessary until EXIT is displayed then press the
(+)
button to exit
that sub-menu.
TO TURN AUDIO SYSTEM ON/OFF
From the AUDIO screen:
1. Press the
(+)
button to display POWR -.
2. Press the
(+)
button to display POWR + and turn the audio system ON. Press the
(-)
button to
display PWR - and turn the audio system OFF.
IMPORTANT:
The power can take a few seconds to turn on or off.
TO ADJUST VOLUME
From the AUDIO screen:
1. Press the
(+)
button to display POWR.
2. Press the MODE (
) button to display VOL.
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
Page 20
Operating Instructions
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
