Page 13
Operating Instructions
S
tandard
lcd c
ontrol
P
anel
The control panel provides a quick visual check of the spa’s status and
allows the user to set the temperature, activate the jets & lights, lock the
temperature and/or spa functions. Other optional functions may also be
available depending on the spa model and accessory equipment that has
been installed into the spa. The Control panel has eight buttons.
HARD BUTTONS
The four labeled outer buttons are referred to as "Hard buttons". These
buttons are fixed and their functions do not change.
JETS -
If jet pump indicator light is off and JETS hard button is pressed,
the 1st jet pump function will activate and the Control panel display will
advance to the Jets menu.
If jet pump indicator light is on and the JETS hard button is pressed while
in any screen other than the Jets menu, the jets pump function does not
change, only the Control panel screen will change to the Jets menu.
LIGHTS
- If lights are off, press LIGHTS hard button from any screen to
turn on the Underwater lights (only) and display the Underwater Lighting
menu. When LIGHTS hard button is pressed in the Underwater Lighting
menu with the underwater lights on, it will cycle the light intensity for the
underwater lights. If underwater lights are on, initial press of LIGHTS hard
button will not change light setting but will access Underwater lighting
menu.
OPTIONS
- Transitions to the Options screen to access temperature and
setup menu
BACK
- Goes back one menu. In Home screen Hold BACK button until
screen rotates 180° to view from inside spa. Repeat to reverse.
SOFT BUTTONS
The four inside buttons are referred to as "soft buttons". Pressing a soft
button will activate the function on the control panel screen closest to that
button. The control panel display lets you know you’ve pressed a button
and that the selected function has been performed. After a period of non-
use (45 seconds) the display will go back to the Home screen where the
screen will remain on for several minutes before going into sleep mode.
Pressing any button will wake up a sleeping display.
INDICATOR ICONS
The indicator icons can only be seen on the Home Screen. They are
visible whenever the icons function is active.
READY Indicator:
The READY indicator icon is displayed
when the spa water temperature is within 1°C (2°F) of the set
temperature, and will turn off when the temperature is outside of that
range. If you increase or decrease the temperature setting of the spa,
the READY indicator icon will turn off until the water temperature
reaches the acceptable range for the new temperature setting. A
flashing READY indicator icon means a problem may exists with the
temperature sensor (see Troubleshooting section for more information)
Spa Light Indicator:
The Spa Light indicator icon is displayed
when any light inside the spa is on. The indicator will remain
solid as long as any light is activated. Spa Light indicator flashes
whenever the color wheel is on.
Spa or Temperature Lock Indicator:
The Spa or
Temperature Lock indicator icon is displayed when either the
Spa Lock, Temperature Lock or both is activated. Lock indicator icon
does not flash.
Jet Pump Indicator:
The Jet Pump indicator icon is displayed
whenever a jet pump is on. The Jet Pump indicator icon will
flash whenever the spa is in the ten-minute clean cycle.
Summer Timer Indicator:
The Summer Timer indicator icon
is displayed when the summer timer is set to ON. In the
summer timer mode, the heater and circulation pump cycle are off for
eight hours. The Summer Timer indicator icon will not flash.
Water Care Indicator:
The Water Care indicator icon is
displayed whenever a water care device is detected in the
system and the water care system is operating correctly. The icon will
flash if the water care system requires attention.
POWER Indicator:
The POWER indicator icon is displayed
when the spa is properly supplied with power. It also provides
a diagnostic function–a flashing Power indicator icon indicates that the
heater high limit has tripped, meaning that either the spa water is above
its acceptable temperature range, or a malfunction has occurred within
the spa (such as low circulation due to clogged filters). An ‘off’ power
indicator icon means that there is a problem with the spa control box or
the power supplied to the spa (see Troubleshooting section for more
information).
OPTION SCREEN
The Option screen is an intermediate
screen that gets you to various
optional settings.
Press the OPTIONS hard button
on the control panel to display the
Options screen.
Press the Soft button next to
the descriptions to access the
description's screen.
IMPORTANT
: Audio and ACE Water Care will only be displayed on your
Options screen if your spa is equipped with these features.
JETS
Hard button
Soft buttons
Indicator Icons
Control panel screen
LIGHTS
Hard button
OPTIONS
Hard button
BACK
Hard button
