Page 36
FIlTER CARTRIdgE REMOVAl & ClEANINg
1. disconnect the spa from the power supply by tripping both of the GFcI breakers located in the subpanel.
2. Remove and carefully set aside the filter compartment cover.
3. Remove any floating items from within the filter compartment.
4. Turn the filter retainer handle (located on the top of the filter cartridge) counterclockwise until the retainer can be removed from the filter standpipe.
5. Remove the filter retainer and cartridge.
SERVICE NOTE:
Never remove the filter standpipe when debris is present in the filter compartment. debris may find its way into the internal
plumbing which may result in blockage. NeVeR ReMoVe sucTIoN FITTINGs!
6. Always clean the filter using a filter degreaser, such as
Hot Spring
®
FreshWater
®
Filter cleaner, to remove mineral and oil build-up. simply
soak the filter in the degreaser according to the package directions, then place the filter on a clean surface and spray until clean using a garden
hose. It may be necessary to rotate the filter while spraying to remove any debris lodged between the filter pleats.
7. To reinstall the filter cartridge, reverse the order of steps in which it was removed. do not overtighten
WaRNING:
do not use the spa with the filter cartridge(s), or filter standpipe(s) removed!
CARE OF THE SPA PIllOWS
The pillows used in your
Hot Spring
®
spa will continue to provide comfort if treated with care. They have been positioned above the water level to
minimize the bleaching effects of chlorinated water, and other spa water chemicals. To extend their life, whenever the spa shell is being cleaned,
the spa pillows should be removed and cleaned. Body oils can be removed with a mild soap and water solution. ALWAys rinse off the spa pillows
thoroughly to remove any soap residue. The pillows can be conditioned with
Hot Spring
cover shield after cleaning. If the spa is not going to be
used for a long period of time (that is during a vacation, or if the spa is winterized), or when the spa water is being super-chlorinated, the spa pillows
should be removed until the next spa use. Periodic replacement of the spa pillows will be necessary in order to maintain the new look of your spa.
To reMove and rePLaCe THe SPa PILLoWS:
1. carefully pull and lift on one end of pillow to stretch pillow (longer) until the pillow is released from the plastic retainer. once one end is
released, push pillow in opposite direction to remove from other retainer.
2. Align pillow.
3. slide one end of pillow onto the spa retainer.
4. Pull other end of pillow; using both hands lift pillow above retainer and with a stretching motion slide pillow recess onto retainer.
CARE OF THE EXTERIOR
SPa SHeLL
your
Hot Spring
®
spa has an acrylic shell. Stains and dirt generally will not adhere to your spa’s surface. A soft rag or a nylon scrubber should
easily remove most dirt. Most household chemicals are harmful to your spa’s shell. Watkins Manufacturing Corporation recommends
Hot Spring
FreshWater
®
spa shine. cleaning of the surface should only be done with a non-abrasive, non-sudsing cleaner. sodium bicarbonate (baking
soda) can also be used for minor surface cleaning. A soft rag or a nylon scrubber should easily remove most dirt. Always thoroughly rinse off any
spa shell cleaning agent with fresh water.
SERVICE NOTES:
1. Iron and copper in the water can stain the spa shell if allowed to go unchecked. Ask your
Hot Spring
dealer about a stain and scale Inhibitor
such as
Hot Spring
®
FreshWater
®
stain and scale defense to use if your spa water has a high concentration of dissolved minerals.
2. The use of alcohol or any household cleaners other than those listed to clean the spa shell surface is NoT recommended. do NoT use any
cleaning products containing abrasives or solvents since they may damage the shell surface.
NEVER USE HARSH CHEMICALS!
damage to
the shell by the use of harsh chemicals is not covered under the warranty.
ImpORTaNT:
Some surface cleaners contain eye and skin irritants. Keep all cleaners out of the reach of children and use care when applying.
EVERWOOd
®
SPA CAbINET
Hot Spring
spas include an everwood spa cabinet. everwood consists of a rigid polymer that combines the durability of plastic, with the beauty of
wood. Everwood won’t crack, peel, blister, or delaminate even after prolonged exposure to the elements.
cleaning of everwood consists of simply spraying the cabinet with a mild soap and water solution to remove any stains and residue.
do not rub the everwood with an abrasive material or use abrasive cleaners, as this may damage its texture.
Watkins Manufacturing corporation recommends touch-up or restaining of the everwood every three to four years (this will vary according to the
environment). contact your local dealer for restaining procedures and recommended stains.
Spa Care and Maintenance
Page 36
Spa Care and Maintenance
Summary of Contents for Limelight
Page 1: ......
