background image

GEA19684  ISRB_2008 rev._11.15

2

Do these things to get the most from your Roots Blower

Roots products are sold subject to the current General Terms of Sale, ES104 and Warranty Policy WP-5020.  
Copies are available upon request. 

Contents

Information Summary ...............................................................2

Safety Precautions ....................................................................3

Operating Limitations ................................................................3

Installation ........................................................................... 4 - 6

Lubrication ................................................................................7

Operation ..................................................................................8

Troubleshooting ........................................................................9

Inspection & Maintenance ......................................................10

Figures ............................................................................ 11 - 12

Tables .....................................................................................13

Parts List .................................................................... 14, 17, 19

Assembly Drawings ...........................................15 - 16, 18, 20

• 

Check shipment for damage. If found, file claim with 
carrier and notify Howden.

• 

Unpack shipment carefully, and check contents against 
Packing List. Notify Howden if a shortage appears.

• 

Store in a clean, dry location until ready for installation. 
Lift by methods discussed under INSTALLATION to 
avoid straining or distorting the equipment. Keep covers 
on all openings. Protect against weather and corrosion 
if outdoor storage is necessary.

• 

Read OPERATING LIMITATIONS and INSTALLATION 
sections in this manual and plan the complete 
installation.

• 

Provide for adequate safeguards against accidents 
to persons working on or near the equipment 
during both installation and operation. See SAFETY 
PRECAUTIONS.

• 

Install all equipment correctly. Foundation design 
must be adequate and piping carefully done. Use 

recommended accessories for operating protection.

• 

Make sure both driving and driven equipment is 
correctly lubricated before start-up. See LUBRICATION.

• 

In event of trouble during installation or operation, do 
not attempt repairs of Roots furnished equipment. 
Notify Roots, giving all nameplate information plus an 
outline of operating conditions and a description of the 
trouble. Unauthorized attempts at equipment repair 
may void Roots warranty.

• 

Units out of warranty may be repaired or adjusted by 
the owner. Good inspection and maintenance practices 
should reduce the need for repairs. 

NOTE:

 Information in this manual is correct as of the date 

of publication. Howden reserves the right to make design or 
material changes without notice, and without obligation to make 
similar changes on equipment of prior manufacture.

For your nearest Howden Office, dial our Customer Service 
Hot Line toll free in the U.S.; 1 877 363 7668 or 1 

GEA19684_ISRB-2008_Tri-RAM_rev02.16.indd   2

15/02/2016   11:17:05

Summary of Contents for Roots Tri-RAM 409























Reviews: