Hozelock Cyprio EasyClear 3000 1760, Installation And Operating Instructions Manual

below the flow control. This is normal in operation.
Position the unit in the pond. The fountain angle can 

be adjusted to be vertical using the ball joint (Fig 2-A).
The tightness of the ball joint can be adjusted (Fig 2-J).
If required, the 2-Tier Fountainhead can be used to 

achieve an alternative and higher display pattern than  

the 3-Tier.
The fountain height can be adjusted to suit your needs 

by rotating the Fountain Flow Adjuster (Fig 3-K).
The Bell Fountain creates a decorative waterbell. The 

size of the bell can be adjusted to suit your needs by 

rotating the Fountain Flow Adjuster (Fig 3-K).

Waterfall Only Operation

(Fig 4-B for general installation guide)
Position the pump as previously described.
Attach a suitable length (3m maximum) of 25 mm (1”) 

hose to the waterfall hose tail (Fig 1-G) and secure 

with a suitable hose clip and position the outlet end of 

the hose in the desired position.
Screw the waterfall hose tail to the fountain outlet of 

the EasyClear™ (Fig 1-A) and adjust the flow using the 

fountain flow adjuster, (Fig 3-K), to suit your needs.
Note: The maximum recommended waterfall height 

above pond level is 0.5m (Fig 4-B).

UVC Operation

The UVC will automatically switch on once the unit 

has been connected to the electricity supply if the 

bayonet tube is correctly locked in place.
The UVC lamp can be checked for operation by 

looking for a bluish glow from ball joint outlet (Fig 

1-A). Please note that this may only become visible in 

low light conditions.
See Maintenance section for Lamp replacement.

Maintenance

The Hozelock Cyprio EasyClear™ has been designed 

to allow fast and easy maintenance. As with all pond 

equipment, occasionally it will become necessary to 

clean or replace parts.
WARNING: Disconnect this product from the 

electricity supply and refer to the section “Safety 

& Electrical Connections” before attempting any 

maintenance.
Fountain Head (Fig 1-I)
Follow the below procedure if the fountain head is 

blocked:
1 -   Place a coin or similar in the slot and gently lever 

off the fountain head.

2 -   Rinse in clean water and reassemble.

Foam
Follow the below procedure if flow appears reduced:
1 -   Release the Foam Cover by pushing the two 

buttons (Fig 5-M) and lift the cover (Fig 6-N).

2 -   Remove the Foam (Fig 7-O). Note:- If the unit is 

out of the pond for more then 20 minutes the 

biological filter action may stop working. Rinse 

thoroughly in pond water (do not use tap water).

3 -   The Foam Cover and Base should also be rinsed in 

pond water (do not use tap water).

4 -   It may also be necessary to clean out the 

biomedia and stones (Fig 7-P) if these have 

become clogged. If this is necessary, the biomedia 

and stones should be rinsed in pond water only.

5 - Reassemble the Filter.
Quartz Tube
Follow the below procedure if your pond remains 

green:
1 -   Remove the bayonet locking screw (Fig 8-Q), twist 

and lift the bayonet tube (Fig 8-R).

2 -   Clean the Quartz Tube. Take extra care when 

handling the Quartz tube. In hard water areas, 

the quartz tube may become covered in limescale, 

which will reduce efficiency. Clean the tube with a 

soft cloth and a gentle de-scaler (such as vinegar 

and water), rinse in water before refitting.

3 -  Reassemble the bayonet tube and screw and 

restart (Fig 8-S).

Warning! Ensure that the quartz tube is not 

damaged before refitting.
Lamp Replacement
Follow the below procedure if the lamp needs 

replacing or does not illuminate:
Change the lamp at the start of the new season. Even 

though the lamp still glows it may not be giving out 

anyuseful UV radiation. How well the EasyClear™ 

performs is related to the strength of the UV radiation 

produced. This will slowly decline from the day your 

lamp is switched on. The UVC lamp has an effective 

life of 12 months. You need to change the lamp when 

there is a significant reduction in water clarity. Make 

sure this is due to an expired lamp and not a badly 

maintained filter or a dirty/limescaled quartz sleeve. 

Both can greatly reduce UV transmission into the 

water.
1 -   Remove the bayonet locking screw (Fig 8-Q), twist 

and lift the bayonet tube (Fig 8-R).

2 -   Unscrew the quartz tube locking collar (Fig 9-T-i). 

Gently hold the quartz tube (Fig 9-T-ii), lift up and 

remove together with its o-rings (Fig 9-T-iii) and 

locking collar.

3 -   Remove the old lamp by gently pulling it from 

its holder (Fig 9-U). Dispose of the old lamp