background image

Section 1 - General Information

1.1  Warranty

Thank you for your purchase.  We are confident it will serve you for a long time.  Our warranty to you
is as follows:

The manufacturer agrees to correct for the original user of this product, either by repair, or at the
manufacturer’s election, by replacement, any defect  which develops after delivery of this product
within the period as stated on the warranty card.  In the event of replacement, the replacement unit
will be warranted for 90 days or warranted for the remainder of the original unit’s parts or labor
warranty period, whichever is longer.

If this product should require service, contact the manufacturer/suppliers’ office for instructions. When
return of the product is necessary, a return authorization number will be assigned and the product
should be shipped, transportation charges pre-paid, to the indicated service center.  To insure prompt
handling, the return authorization number should be placed on the outside of the package and a
detailed explanation of the defect enclosed with the item.

This warranty shall not apply if the defect or malfunction was caused by accident, neglect,
unreasonable use, improper service, or other causes not arising out of defects in material or
workmanship.  There are no warranties, expressed or implied, including, but not limited to, those of
merchantability or fitness for a particular purpose which extends beyond the description and period
set forth herein.  The manufacturer’s sole obligation under this warranty is limited to the repair or
replacement of a defective product and the manufacturer shall not, in any event, be liable for any
incidental or consequential damages of any kind resulting from use or possession of this product.

Some states do not allow: (A) limitations on how long an implied warranty lasts or (B) the exclusion or
limitation of incidental or consequential damages, so the above limitations or exclusions may not
apply to you.  This warranty gives you specific legal rights.  You may have other rights which vary
from state to state.

1.2  Unpacking

Your recirculating chiller is shipped in a special carton.  Retain the carton and all packing materials
until the unit is completely assembled and working properly. Set up and run the unit immediately to
confirm proper operation.  Beyond one week, your unit may be warranty repaired, but not replaced.  If
the unit is damaged or does not operate properly, contact the transportation company, file a damage
claim, then contact the company where your unit was purchased. 

1.3  Package Contents

– Recirculating Chiller

– Operators Manual

– Warranty Card

– 2 sets of Inlet/Outlet Adapters: 1/2 inch I.D. tubing; 5/8 inch I.D. tubing

– Durable Tubing, 1/2 inch I.D.

1.4  Description

These chillers provide cooling power for demanding applications, and economically replace tap water
cooling systems.  All models have a microprocessor controller, digital set/read and readout in °C or
°F.  The refrigeration system has modulation capability to provide cooling as needed and thus greater
temperature stability and longer compressor life.  Wetted parts are brass, copper, polypropylene,
PVC, nylon and stainless steel.

3

Summary of Contents for 6105P















Reviews: