background image

Regulatory Information

Laser Safety Statements

Appendix A

19

CAUTION

The optical transceiver provided on the network interface card contains a laser system and is
classified as a “Class 1 Laser Product” per EN 60825-1, Safety of Laser products. Class 1 laser
products are considered safe and do not pose a biological hazard if used within the data sheet
limits and instructions.

To ensure proper use of this product, please read this instruction manual carefully and retain for future
reference. Should the unit ever require maintenance, contact an authorized service location.

CAUTION

Use of controls, adjustments or the performance procedures other than those specified herein
may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not
try to open the enclosure.

There are no user serviceable parts nor any maintenance required for the optical transceiver. All adjustments
are made at the factory before shipment to customers. Tampering with or any attempt to modify the optical
transceiver will result in voided product warranty. It may also result in improper operation of the network
card circuitry and possible overstress of the laser source. Device degradation or product failure may result.

Summary of Contents for A6795A





















Reviews: