background image

Perforate

HP Customer Support Services

The warranty booklet shipped with the HP Remote 2C describes the support for this 
product. For module updates, see HP’s Web Site. For white papers and module updates, 
see HP’s web site or HP’s fax retrieval service as described below.

World Wide Web

http://www.hp.com/go/network_city

 

From this web site, you can access information on the HP networking products. If you 
have a growing network, download the 

Designing HP AdvanceStack Networks Guide

 

or call 1-800-752-0900 in the U.S. to receive a copy through the mail.

HP FIRST Fax Retrieval Service

HP FIRST is an automated fax retrieval service that is available 24 hours a day, seven 
days a week. HP FIRST provides information on the following topics:

Product information

Troubleshooting instructions

Technical reviews and articles

Configuration information

To access HP FIRST, dial one of the following phone numbers:

(Please turn over for additional HP Support)

Location

Phone Number

U.S. and Canada Only

Dial 1 (800) 333-1917 with your fax machine or touch-tone phone 
and press 1.

Outside the U.S. and Canada 

Dial 1 (208) 344-4809 from your fax machine and press 9. 

To receive a list of currently available documents, enter document number 19941. The information 
you requested will be sent to you by return fax. For other countries, see http://www.hp.com/
cposupport/eschome.html.

abner.bk : 0_perf.fm5  Page 3  Monday, June 23, 1997  2:40 PM

Summary of Contents for AdvanceStack Remote 2C





































Reviews: