background image

8

HP Part Number 5990-3463

Warranty and Support

This HP Server rail kit is covered by a limited hardware warranty for a period of one year from receipt by the original
end-user purchaser.

Once installed in an HP Server, this accessory may carry the longer of either a one-year warranty or the remainder of the
warranty period for the HP Server in which it is installed.

This accessory may be serviced through expedited part shipments. In this event, HP will prepay shipping charges, duty,
and taxes; provide telephone assistance on replacement of the component; and pay shipping charges, duty, and taxes for
any part that HP asks to be returned.

The customer may be required to run HP-supplied configuration and diagnostic programs before a replacement will be
dispatched or an on-site visit is authorized.

Refer to the warranty statement provided with your original HP Server system documentation for the warranty
limitations, customer responsibilities, and other terms and conditions.

HP Repair and Telephone Support

Refer to the Warranty & Support for your HP Server booklet supplied with your HP Server system documentation for
instructions on how to obtain HP repair and telephone support.

Summary of Contents for C5687A - SureStore DAT 40i Tape Drive









Reviews: