background image

2–6

433611-001

Service Reference Guide, dx7300

Setup Utilities and Diagnostics Features

Storage 

(continued)

Device 

Configuration 

(continued)

Multisector Transfers 

(ATA disks only)

Specifies how many sectors are transferred per multi-sector PIO 

operation. Options (subject to device capabilities) are Disabled, 8, 

and 16.

Transfer Mode 

(IDE devices only)

Specifies the active data transfer mode. Options (subject to device 

capabilities) are PIO 0, Max PIO, Enhanced DMA, Ultra DMA 0, 

and Max UDMA.

Translation Mode 

(ATA disks only)

Lets you select the translation mode to be used for the device. This 

enables the BIOS to access disks partitioned and formatted on other 

systems and may be necessary for users of older versions of UNIX 

(e.g., SCO UNIX version 3.2). Options are Automatic, Bit-Shift, 

LBA Assisted, User, and None

Ä

CAUTION:

 Ordinarily, the translation mode selected 

automatically by the BIOS should not be changed. If the selected 

translation mode is not compatible with the translation mode that 

was active when the disk was partitioned and formatted, the data 

on the disk will be inaccessible.

Translation Parameters 

(ATA disks only)

This feature appears only when User translation mode is selected.

Allows you to specify the parameters (logical cylinders, heads, and 

sectors per track) used by the BIOS to translate disk I/O requests 

(from the operating system or an application) into terms the hard 

drive can accept. Logical cylinders may not exceed 1024. The 

number of heads may not exceed 256. The number of sectors per 

track may not exceed 63. These fields are only visible and 

changeable when the drive translation mode is set to User.

Default Values IDE/SATA

Allows you to specify the default values for the Multisector Transfers, 

Transfer Mode, and Translation Mode for ATA devices.

Storage Options

Removable Media Boot

Enables/disables ability to boot the system from removable media.

Legacy Diskette Write

Enables/disables ability to write data to legacy diskettes.

After saving changes to Removable Media Write, the computer 

will restart. Turn the computer off, then on, manually.

BIOS DMA Data Transfers

Allows you to control how BIOS device I/O requests are serviced. 

When “Enable” is selected, the BIOS will service ATA device read 

and write requests with DMA data transfers. When “Disable” is 

selected, the BIOS will service ATA device read and write requests 

with PIO data transfers.

Heading

Option

Description

Support for specific Computer Setup options may vary depending on the hardware configuration.

Summary of Contents for Compaq dx7300











































































































































































































































Reviews: