background image

Service Reference Guide, dx7300

433611-001

C–9

POST Error Messages

POST Diagnostic Front Panel LEDs and Audible Codes

This section covers the front panel LED codes as well as the audible codes that may occur before 
or during POST that do not necessarily have an error code or text message associated with them.

Å

WARNING: 

When the computer is plugged into an AC power source, voltage is always applied to the 

system board. To reduce the risk of personal injury from electrical shock and/or hot surfaces, be sure to 

disconnect the power cord from the wall outlet and allow the internal system components to cool before 

touching.

Look for the LED between the DIMM sockets. If the LED is illuminated, the system still has power. Power off 

the computer and remove the power cord before proceeding.

If you see flashing LEDs on a PS/2 keyboard, look for flashing LEDs on the front panel of the 
computer and refer to the following table to determine the front panel LED codes.

Recommended actions in the following table are listed in the order in which they should be 
performed.

No all diagnostic lights and audible codes are available on all models.

POST Diagnostic Front Panel LEDs and Audible Codes

Activity

Beeps

Possible Cause

Recommended Action

Green Power LED 

On.

None

Computer on.

None

Green Power LED 

flashes every two 

seconds.

None

Computer in 

Suspend to RAM 

mode (some 

models only) or 

normal Suspend 

mode.

None required. Press any key or move the 

mouse to wake the computer.

Red Power LED 

flashes two times, 

once every 

second, followed 

by a two second 

pause. Beeps stop 

after fifth iteration 

but LEDs continue 

until problem is 

solved.

2

Processor thermal 

protection 

activated:
A fan may be 

blocked or not 

turning.
OR 
The heatsink/fan 

assembly is not 

properly attached 

to the processor. 

1. Ensure that the computer air vents are 

not blocked and the processor cooling 

fan is running.

2. Open hood, press power button, and 

see if the processor fan spins. If the 

processor fan is not spinning, make 

sure the fan's cable is plugged onto 

the system board header.

3. If fan is plugged in, but is not 

spinning, then replace heatsink-fan 

assembly.

Summary of Contents for Compaq dx7300











































































































































































































































Reviews: