HP P2000 G3 Cli Reference Manual Download

Page: 231 / 532

HP P2000 G3 MSA System CLI Reference Guide 231

show expander-status

Description For use by or with direction from a service technician.

Shows diagnostic information relating to SAS Expander Controller physical channels, known as PHY

lanes. For each enclosure, this command shows status information for PHYs in I/O module A and

then I/O module B.

Syntax

show expander-status

Output

Encl

Enclosure that contains the SAS expander.

Ctlr

I/O module that contains the SAS expander.

Phy

Identifies a PHY’s logical location within a group based on the PHY type. Logical IDs are 0–23 for

drive PHYs; 0–1 for SC PHYs; and 0–3 for other PHYs. If the PHY's controller module or expansion

module is not installed, this field shows “

”.

Type

•

Drive

: 1-lane PHY that communicates between the expander and a disk drive.

•

Egress

: 4-lane PHY that communicates between the expander and an expansion port or SAS

Out port.

•

SC-1

: (Controller module only) 2-lane PHY that communicates between the expander and the

partner’s expander.

•

SC-0

: (Controller module only) 4-lane PHY that communicates between the expander and the

SC.

•

Ingress

: (Expansion module only) 4-lane PHY that communicates between the expander and

an expansion port.

•

Inter-Exp

: (Expansion module only) Communicates between the expander and the partner’s

expander.

•

Undefined

: No status information is available.

•

Unused

The PHY exists in the expander but is not connected, by design

Status

•

Enabled - Healthy

: The PHY is enabled and healthy.

•

Enabled - Degraded

: The PHY is enabled but degraded.

•

Disabled

: The PHY has been disabled by a user or by the system.

Elem Status

A standard SES status for the element:

•

Disabled

: Critical condition is detected.

•

Error

: Unrecoverable condition is detected. Appears only if there is a firmware problem related

to PHY definition data.

•

Non-critical

: Non-critical condition is detected.

•

Not Used

: Element is not installed in enclosure.

•

: Element is installed and no error conditions are known.

•

Unknown

: Either:

• Sensor has failed or element status is not available. Appears only if an I/O module indicates

it has fewer PHYs than the reporting I/O module, in which case all additional PHYs are

reported as unknown.

• Element is installed with no known errors, but the element has not been turned on or set into

operation.

Summary of Contents for P2000 G3





















































































































































































































































































































































































































































































































































Search results

Summary of Contents for P2000 G3

Reviews:

Related manuals for P2000 G3

Brands by name

Popular brands

HP P2000 G3, Cli Reference Manual

Search results

Summary of Contents for P2000 G3

Reviews:

Related manuals for P2000 G3

Brands by name

Popular brands