HP P2000 G3 Cli Reference Manual Download

Page: 325 / 532

HP P2000 G3 MSA System CLI Reference Guide 325

show volume-statistics

Description

Shows live performance statistics for all or specified volumes. For each volume these statistics

quantify I/O operations between hosts and the volume. For example, each time a host writes to a

volume’s cache, the volume’s statistics are adjusted.
Properties shown only in XML API format are described in

XML API basetype properties

page 345.

Syntax

show volume-statistics [

volumes

]

Parameters

volumes

Optional. Names or serial numbers of the volumes to show information about. For volume syntax,

see

Command syntax

on page 22. If this parameter is omitted, information is shown for all volumes.

Output

Name

Volume name.

Serial Number

Volume serial number.

Bytes per second

Data transfer rate calculated over the interval since these statistics were last requested or reset. This

value will be zero if it has not been requested or reset since a controller restart.

IOPS

Input/output operations per second, calculated over the interval since these statistics were last

requested or reset. This value will be zero if it has not been requested or reset since a controller

restart.

Number of Reads

Number of read operations since these statistics were last reset or since the controller was restarted.

Number of Writes

Number of write operations since these statistics were last reset or since the controller was restarted.

Data Read

Amount of data read since these statistics were last reset or since the controller was restarted.

Data Written

Amount of data written since these statistics were last reset or since the controller was restarted.
Reset Time

Date and time, in the format

year

month

day

hour

minutes

seconds

, when these statistics

were last reset, either by a user or by a controller restart.

Example

Show statistics for volume

vd1_v001

# show volume-statistics vd1_v001

Name Serial Number Bytes per second IOPS Number of Reads

Number of Writes Data Read Data Written Reset Time

-----------------------------------------------------------------------------

vd1_v001

5696.0KB 236 44091454

60342344 1133.0GB 1378.9GB 2012-01-20 10:14:54

-----------------------------------------------------------------------------

Success: Command completed successfully. (2012-01-20 12:44:50)

Basetypes

•

volume-statistics

•

status

Summary of Contents for P2000 G3





















































































































































































































































































































































































































































































































































Search results

Summary of Contents for P2000 G3

Reviews:

Related manuals for P2000 G3

Brands by name

Popular brands

HP P2000 G3, Cli Reference Manual

Search results

Summary of Contents for P2000 G3

Reviews:

Related manuals for P2000 G3

Brands by name

Popular brands