background image

Step 4: Fully recharge the battery

To recharge the battery:

1.

Plug the computer into external power and maintain external power until the battery is fully
recharged. When the battery is recharged, the battery light on the computer turns off.

You can use the computer while the battery is recharging, but the battery will charge faster if the
computer is off.

2.

If the computer is off, turn it on when the battery is fully charged and the battery light has turned
off.

Step 5: Reenable Hibernation and Sleep

CAUTION:

Failure to reenable Hibernation after calibration may result in a full battery discharge and

information loss if the computer reaches a critical battery level.

1.

Click the battery meter icon in the notification area, and then click 

More power options

.

– or –

Select 

Start

 

>

 

Control Panel

 

>

 

System and Maintenance

 

>

 

Power Options

.

2.

Under the current power plan, click 

Change plan settings

.

3.

Reenter the settings that you recorded for the items in the 

On battery

 column.

4.

Click 

Change advanced power settings

.

5.

Click the plus sign next to 

Sleep

, and then click the plus sign next to 

Hibernate after

.

6.

Reenter the setting that you recorded for 

On battery

.

7.

Click 

OK

.

8.

Click 

Save changes

.

Calibrating a battery

15

Summary of Contents for Presario A900 - Notebook PC






























Reviews: