Bronze Models GCBN2V, GCBN3V, GCBN22V and GCBN33V
Cast Iron Models GCCV2V, GGCCV3V, GCCV22V and GCCV33V
Shertech Operating Instructions, Performance,
Specifications and Parts Manual
Hypro warrants to the original purchaser of its products (the “Purchaser”) that such products will be free from defects in
material and workmanship under normal use for the period of six (6) months, and accessories will be free from defects in
material and workmanship under normal use for the period of ninety (90) days. Parts carry no warranty.
“Normal use” does not include use in excess of recommended maximum speeds, pressures, vacuums and temperatures, or
use requiring handling of fluids not compatible with component materials. This warranty does not cover freight damage,
freezing damage, pump or motor damage from incorrect wiring (if equipped with motor), normal wear and tear, or damage
caused by misapplication, fault, negligence, alterations, dry running pump, or repair that affects the performance or
reliability of the product.
THIS WARRANTY IS EXCLUSIVE. HYPRO MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Hypro’s obligation under this warranty is, at Hypro’s option, to either repair or replace the product upon return of the entire
product to the Hypro factory in accordance with the return procedures set forth below.
THIS IS THE EXCLUSIVE REMEDY FOR
ANY BREACH OF WARRANTY.
IN NO EVENT SHALL HYPRO BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, WHETHER FOR
BREACH OF ANY WARRANTY, FOR NEGLIGENCE, ON THE BASIS OF STRICT LIABILITY, OR OTHERWISE.
Only authorized distributors can return products for Warranty. Contact your distributor or visit www.shertech.com to find a
distributor for product support.
Distributors can obtain an RMA # and contact person’s name by contacting Hypro’s customer service at 800-471-0460.
Return Procedures for Distributors
All pumps or products must be flushed of any chemical (ref. OSHA Section 0910.1200 (d)(e)(f)(g)(h) and hazardous chemicals
must be labeled before being shipped* to Hypro for service or warranty consideration. Hypro reserves the right to request a
Material Safety Data sheet from the Purchaser for any pump or product Hypro deems necessary. Hypro reserves the right to
“disposition as scrap” pumps or products returned without authorization and/or which contain unknown substances, or to
charge for any and all costs incurred for chemical testing and proper disposal of components containing unknown substances.
Hypro requests this in order to protect the environment and personnel from the hazards of handling unknown substances.
Be prepared to give Hypro full details of the problem, including the following information:
1. Model number, sale record/invoice, purchase date and from whom you purchased your pump.
2. A brief description of the pump problem, including the following:
• Liquid pumped. State the pH and any non-soluble
• Drive type (gas engine/electric motor; direct/belt drive;
materials, and give the generic or trade name.
tractor PTO) and rpm of pump.
• Temperature of the liquid and ambient environment.
• Viscosity of fluid if other than water.
• Suction lift or vacuum (measured at the pump).
• Specific gravity of fluid if other than water.
• Discharge pressure.
• Elevation from the pump to the discharge point.
• Size, type, and mesh of the suction strainer.
• Size and material of suction and discharge line.
• Abrasiveness or particulate size in fluids.
Hypro may request additional information and may require a sketch to illustrate the problem. Distributors should contact the
factory to receive a return material authorization before sending the product. All pumps returned for warranty work should
be sent shipping charges prepaid to:
[RMA# and Contact Person]
HYPRO
375 Fifth Avenue NW
New Brighton, Minnesota 55112
NOTE:
Hypro reserves the right to “disposition as scrap” pumps or products returned without authorization.
*Carriers, including U.S.P.S., airlines, UPS, ground freight, etc., require specific identification of any hazardous materials being shipped.
Failure to do so may result in a substantial fine and/or prison term. Check with your shipping company for specific instructions.
Limited Warranty on Carbonator-Mount
Rotary Close-Coupled External Gear Pumps
Form L-4083 (1/06)
Printed in USA
