background image

the special adjustment recommended by the manufacturer). 

F)

 

Safety  glasses  should  be  worn  during  any  operation  such  as  preparation, 

operation and maintenance. 
2.3:Operation 

A

hands and feet must not be close to or under rotating parts. 

B

Special care should be taken when operating on (or through) gravel pavements, 

pavements  or  highways  to  guard  against  potential  dangers,  pay  attention  to  traffic 
conditions and do not carry passengers. 

C

After  hitting  the  sundries,  stop  the  engine  (motor)  and  check  whether  the 

cultivator is damaged comprehensively. If damaged, the cultivator can only be restarted 
and operated after repair. 

D)

 

Always watch your step to avoid slipping or falling. 

E)

 

Once  abnormal  vibration  occurs,  the  machine  should  immediately  stop  the 

engine (motor) to find the cause, vibration is usually the precursor of failure. 

F)

 

When leaving the control position, stop the engine (motor) before cleaning up 

blade blockage and during maintenance, adjustment or inspection. 

G)

 

When the machine is unattended, all possible precautions should be taken: 

disconnect the power output shaft, lower the attachment, stall the engine and remove 
the switch key. 

H)

 

Before cleaning, repairing or inspecting the machine, the engine should be 

turned off and all moving parts should be in a stop state. 

I)

 

Exhaust fumes from the engine are harmful. Do not operate indoors. 

J)

 

No  tillage  machine  shall  be  operated  without  proper  protective  device, 

protective cover or other protective device in place. 

K)

 

Stay away from children and pets. 

L)

 

Do not overload the machine due to the high depth and speed of ploughing. 

M)

 

The machine must not run at high speed on slippery roads. Observe the back 

and operate carefully when going backwards. 

N)

 

No bystanders are allowed to approach the machine while it is in operation. 

O)

 

Only additional devices and equipment (such as wheel weights, balancing 

blocks, cab, etc.) permitted by the tiller manufacturer shall be used. 

P)

 

Do not operate the cultivator when vision or light is poor. 

Q)

 

Care should be taken when tilling hard ground. Blades may hook into the 

ground and  push the  tiller  forward.  If  this  happens,  release  the  handrail  and do not 
control the machine. 

R)

 

Cultivators are not allowed to work on steep slopes. 

S)

 

Tilting should be prevented when the cultivator goes downhill. 

2.4:Maintenance and storage 

A)

 

Keep  machines,  accessories  and  equipment,  including  batteries,  in  safe 

working condition. If possible, remove the battery for storage to prevent freezing and 
charge properly if necessary. 

B)

 

Check  whether  the  shear  bolts,  engine  fixing  bolts  and  other  bolts  are 

tightened properly at regular intervals to ensure that the machine is in a safe working 
state. 

Summary of Contents for GT1050B





















Reviews: