background image

 

 

A / V Switch-Cat

 TM

3

 

 

Table of Contents 

1.0 General .............................................................................................. 4

 

2.0 Features.............................................................................................. 4

 

3.0 Installation ......................................................................................... 5

 

4.0 Operation ........................................................................................... 7

 

5.0 Windows™ Projector Configuration Software.................................. 9

 

.   Installing the Software......................................................................... 9

 

.   Selecting your Projector Configuration file......................................... 9

 

.   Creating the Serial Strings ................................................................. 10

 

.   Entering ASCII characters into the serial strings............................... 11

 

.   Entering hexadecimal bytes into the serial strings............................. 11

 

.   Entering wait times into the serial strings.......................................... 12

 

.   Entering Carriage Returns into the serial strings ............................... 12

 

.   Selecting the Baud Rate..................................................................... 12

 

.   Setup to Program VSA-31................................................................. 12

 

.   Loading or Saving Configurations .................................................... 13

 

.   Uploading to the VSA-31 .................................................................. 13

 

.   Putting the VSA-31 into Operation ................................................... 13

 

.   Operating the VSA-31 ....................................................................... 13

 

.   Resetting the VSA-31........................................................................ 14

 

6.0 Troubleshooting............................................................................... 14

 

7.0 Specifications................................................................................... 14

 

 

 

Summary of Contents for A/V Switch-Cat VSA-31

















Reviews: