background image

 

MANUAL

 

HK2 – HK4 25-08-2014

 

Page 

 

Control panel

 

 
 

 

 
 

 
 

(A) 

Function button; short press: shifts between boiler and flue gas temperature 

indication; long press: access to parameters behind PIN code 
(B) 

LED indicator 

(C) 

STOP and minor setting button 

(D) 

START and higher setting button 

(E) 

Main fuse 

(F) 

Mains ON/OFF 

 

Detailed description of the boiler (see paragraph 1.1) 

 

1.

 

Control panel 

Loading door 

These dimensions allow easy wood loading 

Primary air setting 

Adjust the primary air necessary for the combustion. 

Secondary air setting 

Adjust the secondary air necessary for the combustion                                                                         

Ash door 

Behind this door, the combustion take place. This door is also 

 

 

used to take away the ashes regularly.         

Flame control sight glass 

This sight glass is used to set up the combustion. 

Tunnel 

This is the heart of the combustion. 

Secondary air exit 

The secondary air enters the combustion in the high 
temperature zone 

Primary air exit 

The primary air is diffused in through the wood logs 

10 

Removable heat plates 

They limit the shooting up of the boilers body and diffuse 

 

 

the primary air 

11 

Tubular heat exchanger 

The tubular heat exchanger  is used to recover the heat from 

 

 

the flue gases. They are equipped with turbulators. 

12 

Flue gas box 

Collect the flue gas and ashes before evacuation. 

13 

Suction fan 

Brings the necessary air for the combustion. 

14 

Cleaning hatch 

The cleaning is regularly done by this hatch. 

15 

Cooling coil 

It serves to cool down the boiler in case of overheating. 

16 

Flow 

17 

Return 

Summary of Contents for HK2





































Reviews: