19
LP-387 REV. 12.15.14
b. The provided mounting bracket must be mounted directly to the center of at least 2 studs using standard steel or stainless steel
¼” x
2 ½
” lag bolts for all models. Be sure the bracket is level and mark the hole location of the bracket height and horizontal stud location.
Ensure the marked holes are located in the center of the building frame (studs).
c. For all EFT models,
2 ½” is the minimum lag bolt length if the bracket is directly on stud. Increase lag bolt length for any materials
covering the studs.
d. Predrill pilot holes on the marked stud locations. The pilot holes for bare studs should be
2” deep for all EFT models. See table below
for pilot hole diameter by wood type. Increase length for any material covering the stud. Ensure that the predrilled holes are straight and
square to the wall. Failure to do so could lead to insufficient support or out of level boiler. See Figure 6.
NOTE:
Bolt must embed into the wood structure a minimum of 2”.
d. Using the predrilled holes, mount the hanger bracket to the building frame (studs) using the appropriately sized standard steel (or
stainless) lag bolt. Hang boiler on the wall mounted bracket. Be sure that the bracket is engaged before letting the boiler hang free.
Slowly release the weight of the boiler while ensuring that the bracket is properly secured. Verify that the boiler is securely mounted
before leaving the boiler unsupervised.
REQUIRED AMOUNT OF BOLTS FOR WALL MOUNTING THE EFT BOILER
MODEL
AMOUNT OF BOLTS
EFT-55
– EFT-110
2
EFT-155
– EFT-285
4
EFT-399
6
PILOT HOLE SIZE BY WOOD TYPE
TYPE
DRILL BIT SIZE
SOFT
3/32
”
HARD
3/16”
If the boiler is not installed vertically plumb, improper and unsatisfactory operation may occur, causing excessive condensation build-up,
nuisance fault codes, and unnecessary maintenance.
2. MOUNTING TO A METAL FRAME
a. The provided mounting bracket must be mounted to the center of at least 2 studs using standard steel or stainless steel toggle bolts
3/16” diameter or larger, and at least 2” long for direct mounting on stud for EFT-55 – 110 models, and 3/8” diameter or larger, and at
least 2” long for EFT-155 – 399 models for direct mounting on at least 18 gauge studs. Be sure the bracket is level and mark the hole
location of the top bracket height and horizontal stud location. Ensure the marked holes are located in the center of the building frame
(studs).
b. 2” is the minimum toggle bolt length if the bracket is directly on stud. Increase length for any materials covering the studs.
c. Predrill holes on the marked stud locations. The predrilled holes should be ½” in diameter for 3/16” bolts, and ¾” in diameter for 3/8”
bolts, to allow for the collapsed wings of the toggle to slide through. Ensure that the predrilled holes are straight and square to the wall.
Failure to do so could lead to insufficient support of out of level boiler. See Figure 6.
d. Using the predrilled holes, mount the hanger bracket to the building frame (studs) with the toggle bolts. Ensure that the bolt toggles
are through the stud and expanded catching the inside of the stud. Tighten the toggle bolt until the mounting bracket is secure. Hang
boiler on the now wall mounted bracket. Be certain that the bracket is engaged before letting the boiler hang free. Slowly release the
weight of the boiler while ensuring the bracket is properly secure. Verify that the boiler is securely mounted before leaving it
unsupervised.
If the boiler is not installed upright and level, improper and unsatisfactory operation may occur, causing excessive condensation build-
up, nuisance fault codes, and unnecessary maintenance.
PART 5 – BOILER PIPING
Failure to follow the instructions in this section WILL VOID the warranty and may result in property damage, serious injury, or death.
Summary of Contents for EFT-110
