background image

49

50

   LP-532 REV. 8.13.2014

LP-532 REV. 8.13.2014

Cascade Master/Slave Setting

Reset Burner Operating Time

Number of Cascade water heater

Reset Igniting Cycles

P-920C

HIGH

C

F

P-920C

HIGH

C

F

P-920C

HIGH

C

F

P-920C

HIGH

C

F

P-920C

HIGH

C

F

P-920C

HIGH

C

F

P-920C

HIGH

C

F

P-920C

HIGH

C

F

P-920C

HIGH

C

F

P-920C

HIGH

C

F

P-920C

HIGH

C

F

P-920C

HIGH

C

F

P-920C

HIGH

C

F

P-920C

HIGH

C

F

P-920C

HIGH

C

F

P-920C

HIGH

C

F

P-920C

HIGH

C

F

P-920C

HIGH

C

F

P-920C

HIGH

C

F

P-920C

HIGH

C

F

P-920C

HIGH

C

F

P-920C

HIGH

C

F

P-920C

HIGH

C

F

P-920C

HIGH

C

F

Press ‘current status button’ for 5 

secs during panel power off to enter 

installer setting mode

Press ‘current status button’ for 5 

secs during panel power off to enter 

installer setting mode

Press ‘current status button’ for 5 

secs during panel power off to enter 

installer setting mode

Press ‘current status button’ for 5 

secs during panel power off to enter 

installer setting mode

Turn the dial until ‘12:dl’ shows up.

Turn the dial until ‘10:Cl’ shows up.

Turn the dial until ‘9:Cn shows up.

Turn the dial to ‘on’ status when 

initial ‘off’ shows up.(Default : off)

Press ‘dial button’ to save the setting.

Press ‘dial button’ to save the setting.

Turn the dial to set the cascade oper-

ation quantity.

Press ‘dial button’ to save the setting.

Turn the dial to “master product is 

01’’,” slave products from the 02 “set.

‘12:dl’ is displayed and then press 

the dial button for one second.

‘10:C’ is displayed and then press 

the dial button for one second.

‘9:Cn’ is displayed and then press 

the dial button for one second.

Press ‘current status button’ for a 

sec to go back to initial status after 

confirmation.

Press ‘current status button’ for a 

sec to go back to initial status after 

confirmation.

Press ‘current status button’ for a 

sec to go back to initial status after 

confirmation.

Turn the dial until ‘11:dr’ shows up.

Turn the dial to ‘on’ status when 

initial ‘off’ shows up. (Default : off)

Press ‘dial button’ to save the setting.

‘11:dr’ is displayed and then press 

the dial button for one second.

Press ‘current status button’ for a 

sec to go back to initial status after 

confirmation.

Chapter 3 How to use control panel

Chapter 3 How to use control panel

COMING SOON

COMING SOON

Summary of Contents for Hydra Smart RT-199

















































Reviews: