background image

 |

 

33

Temperature Switch TS 2-1000

32

 

|  Features

2 FeaTures

The universal Temperature Switch TSM 2100 with seven different functions is 
ideal for all applications where a precise temperature control in heating or 
cooling is required. External temperature sensors will detect temperatures from 
-99°C  to +850°C. The programmable switching temperature can be adjusted 
in 1°C increments. The blue, two line LCD display shows the programmed 
switching temperatures, the current temperature, the setting parameters and the 
min/max temperature. The device is not only understandable and easy to use but 
also contains a number of safety features. A short-circuit within the sensor cable 
or a defective sensor are immediately indicated on the device. The unit can also 
be used in the form of an independent monitor, as a frost guard, as a substitute 
for defective mechanical thermostats or as a digital thermometer. In addition, 
the device has a separate Min/Max alarm setting. If the temperature ranges 
outside of the preset window, a relay will switch each channel individually after 
an adjustable time between 0-8 hrs. Another relay can also be connected to an 
alarm system. And internal beeper will also give an alarm signal if required. All 
parameters are adjustable.

3 general saFeTy InsTrucTIOns

–  This device should not be handled or installed by persons with reduced phy-

sical, sensory or mental capabilities or lack of experience (including chil dren) 
other than if supervised by a trained, responsible person. 

–  Children may not play with this device and should be supervised when pre-

sent. 

–  This device may only be connected to a properly installed power socket. The 

voltage must match the specifications depicted on the nameplate of the unit 
or mentioned in this instruction manual. 

–  Keep the mains power cord away from sharp edges, moisture, heat or oil. 
–  Do not connect the device if the power cord is damaged. In order to avoid 

a hazard or electrocution, a damaged power cord must be replaced 
immediately by our service centre or a similarly qualified person. 

–  If the power cord is damaged unplug the device immediately and replace the 

power cord accordingly by our service centre or a similarly qualified person.

–  Unplug the device if it is not used over a longer period of time. 

–  Keep the packing material and the plastic bags away from infants. There is 

a danger of suffocation. 

–  When installing the device, install all cables so that they do not become a 

tripping hazard or can accidentally be pulled out. 

–  When disconnecting the device from the mains, pull the plug out of the socket. 

Do not pull at the power cord. 

4 saFeTy InsTrucTIOns

When handling electrical devices, the VDE regulations have to be applied. 
Especially VDE 0100, VDE 0550/0551, VDE 0700, VDE 0711 and VDE 860.
–  This device may not be modified in any way. The CE conformity has been 

declared and proven and the corresponding document is deposited with the 
manufacturer.

–  Before opening the device, please disconnect it from the mains and/or make 

sure that it is not connected to an electrical current.

–  Tools may only be used if the device is disconnected from the mains.
–  All connecting cables should regularly be inspected for any damages on the 

insulation.

–  Should any damages be found, disconnect the device immediately from the 

mains and repair or exchange it.

Should there be any open questions on the installation, the devices connected, 
the functions, the maintenance, the safety or any other point concerning this 
device, please contact a specialist or a qualified person. 

Before installing and using this device, please make sure that it and the attached 
devices are suitable and compatible. In no event will liabilities be taken for 
consequential or incidental direct or indirect damages resulting from improper 
use or incorrect installation of the device.

This item was tested and manufactured according to EU regulations 2014/35/
EU und 2004/108/EG and holds the corresponding CE approval. Any 
change of the circuitry or exchange of components other than specified will 
invalidate this approval.

Summary of Contents for TS 2-1000






























Reviews: