background image

 

Table 5-6

 Connections between wires and pins (using a straight-through cable as an example)

Matching Pins of Wires

Wire Color

1

White-Orange

2

Orange

3

White-Green

4

Blue

5

White-Blue

6

Green

7

White-Brown

8

Brown

 

Step 3

Feed the cable into the plug, and crimp the connector, as shown in 

Figure 5-31

.

NOTE

When inserting the cable, check from the side or bore of the plug to ensure that the cable is completely
seated in the plug.

Figure 5-31

 Crimping the connector

 

Step 4

To complete the assembly of the other end, repeat 

Step 1

 through 

Step 3

.

----End

Checking the Appearance of Contact Strips

Context

l

To ensure proper contact between the crimped wires and the wire conductors, the heights
and sizes of the contact strips must be standard and the same.

l

The contact strips must be parallel to each other, with an offset of less than ± 5°. The top
margin of a strip must be parallel to the axis of the connector, with an offset of less than
± 10°.

R250D
Hardware Installation and Maintenance Guide

5 Appendix

Issue 01 (2016-09-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

39

Summary of Contents for 50082920

















































































































Reviews: