Huawei Enterprise S2700 Series Configuration Manual Download | Manualshive

Page: 268 / 354

background image

Supports the configuration of different start time and end time for a single test:

–

Supports three modes of starting tests: immediate, timely, and delayed.

–

Supports several modes of ending tests: automatic, immediate, timely, delayed, and
ending the test when the lifetime of the test expires.

Supports auto distributing the start time and the test interval when several tests are
performed at a time.

l

Supports the auto-delay function, with which the system resources can be effectively
utilized so that tests can be completed within a specified period.

l

Supports the collection of the uni-directional delay statistics and bi-directional delay
statistics. In addition, you can set a threshold and enable collecting statistics about the
packets in the test results that exceed the threshold.

l

Supports the collection of statistics on packet loss in one direction.

l

Supports the flexible alarm mechanism. That is, the upper and lower thresholds are set to
monitor the feature of the tested objects according to their OIDs. When the test result
exceeds the threshold, alarms are triggered based on the preset events.

6.5 Configuring the ICMP Test

This section describes how to configure an Internet Control Message Protocol (ICMP) test to
check the IP network connectivity.

6.5.1 Establishing the Configuration Task

Before configuring an ICMP test, familiarize yourself with the applicable environment, complete
the pre-configuration tasks, and obtain the required data. This can help you complete the
configuration task quickly and accurately.

Applicable Environment

An ICMP test has a similar function with the

ping

command, but its output is more detailed.

Pre-configuration Tasks

Before configuring the ICMP test, configure reachable routes between the NQA client and the
tested device.

Data Preparation

To configure the ICMP test, you need the following data.

No.

Data

1

Administrator name and test name of the NQA test

2

Destination IP address

3

(Optional) source interface that sends test packets, source IP address, size of the Echo-
Request packets, TTL value, ToS, padding character, interval for sending test packets,
and percentage of the failed NQA test

Quidway S2700 Series Ethernet Switches
Configuration Guide - Network Management

6 NQA Configuration

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

258

«
...
266
267
268
269
270
...
»

Summary of Contents for Enterprise S2700 Series



































































































































































































































































































































































Reviews:

No comments

Related manuals for Enterprise S2700 Series

Brand: LaCie Pages: 4

Brand: LaCie Pages: 4

Brand: LaCie Pages: 4

Brand: Lanner Pages: 2

Brand: TFortis Pages: 86

Brand: HARTING Pages: 13

Brand: Dataprobe Pages: 16

NetCon FBR-1409TX

Brand: LevelOne Pages: 88

GS2020E GigaSPIRE BLAST

Brand: Calix Pages: 15

VAR-SOM-MX8M-PLUS

Brand: Variscite Pages: 2

Brand: rtd Pages: 28

VAR-SOM-MX6 HEAT PLATE KIT

Brand: Variscite Pages: 3

Brand: Axtrinet Pages: 49

Brand: Intercel Pages: 17

Brand: Tripp Lite Pages: 2

FaxFinder FF-120

Brand: Multitech Pages: 20

Brand: Adeunis RF Pages: 68

SWC-2100 (VoIP CPE)

Brand: SEOWON INTECH Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands