Huawei Enterprise S2700 Series Configuration Manual Download

Page: 102 / 354

NOTE

The private IP addresses used by a cluster cannot be the same as any IP address on the device.

Run:

auto-build

[

recover

]

A cluster is created automatically.

The

auto-build

command can also be used to add member switches automatically.

For configuration details, see

Adding a Member Switch

----End

3.3.5 Adding a Member Switch

To perform unified management over a switch that is not a member of a cluster, you must first
add the switch to the cluster.

Context

After a cluster is set up, you can add a member switch to the cluster either manually or
automatically.

Procedure

Adding a member switch manually

In this mode, you must manually specify the MAC address of the member switch.

Do as follows only on the administrator switch:

Run:

system-view

The system view is displayed.

Run:

cluster

The cluster view is displayed.

Run:

add-member

[

member-number

]

mac-address

mac-address

[

password

password

]

A member switch is added.

Adding a member switch automatically

In this mode, the administrator switch prompts you whether to add all the existing candidate
switches to the cluster. If the authentication mode is used to add member switches, the
administrator switch quits the action of adding a member switch.

Do as follows only on the administrator switch:

Run:

system-view

The system view is displayed.

Run:

cluster

Quidway S2700 Series Ethernet Switches
Configuration Guide - Network Management

3 HGMP Configuration

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Summary of Contents for Enterprise S2700 Series



































































































































































































































































































































































Search results

Summary of Contents for Enterprise S2700 Series

Reviews:

Related manuals for Enterprise S2700 Series

Brands by name

Popular brands

Huawei Enterprise S2700 Series, Configuration Manual

Search results

Summary of Contents for Enterprise S2700 Series

Reviews:

Related manuals for Enterprise S2700 Series

Brands by name

Popular brands