Huawei Enterprise S2700 Series Configuration Manual Download | Manualshive

Page: 343 / 354

background image

Table 7-1

Time span of each table

Table

Entry Capacity (Byte)

Maximum Time Span(s)

ethernetStatsTable

100

600

historyControlTable

100

600

alarmTable

60

6000

eventTable

60

600

logTable

600

-

prialarmTable

50

6000

NOTE

logTable does not have a time span. Each log entry can have a maximum of 10 pieces of logs. The
excessive logs supersede the older ones in a circular manner.

When an interface board or an interface card is removed, the corresponding entries in the
ethernetStatsTable and historyControlTable become invalid. If the time spans of tables are
respectively set to 600s, the entries in the tables are deleted when the time spans go down
to 0.
If an interface is added before its corresponding entries are deleted from the table, these
entries can take effect again.

7.3 Configuring RMON

This section describes how to monitor the network status and traffic through RMON.

7.3.1 Establishing the Configuration Task

Before configuring RMON, familiarize yourself with the applicable environment, complete the
pre-configuration tasks, and obtain the required data. This can help you complete the
configuration task quickly and accurately.

Applicable Environment

To monitor network status and collect traffic statistics on a network segment, you can configure
RMON.

Enabling the RMON function does not need any special requirement. You can enable it in
advance, or configure it when you suspect that the traffic of the sub-network where interface
resides is abnormal. You can configure RMON depending on actual situations.

It is recommended to configure the statistics table in advance, configure two history control
policies on the interface where the traffic is abnormal, configure the alarm for one or more
suspicious entries, set the high and low thresholds, and view the alarm information.

NOTE

RMON only stores traffic statistics and information or abnormalities but cannot avoid the generation of
these statistics or information. To clear abnormalities, you need to adopt the other management measures.

Quidway S2700 Series Ethernet Switches
Configuration Guide - Network Management

7 RMON Configuration

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

333

«
...
341
342
343
344
345
...
»

Summary of Contents for Enterprise S2700 Series



































































































































































































































































































































































Reviews:

No comments

Related manuals for Enterprise S2700 Series

Brand: D-Link Pages: 2

Brand: Rain Bird Pages: 17

Brand: Idis Pages: 123

Brand: Idis Pages: 29

Brand: Idis Pages: 28

DirectIP DR-1304P

Brand: Idis Pages: 82

Brand: iDirect Pages: 130

Brand: Paradyne Pages: 45

Brand: peplink Pages: 2

Brand: Garland Pages: 43

Brand: Moxa Technologies Pages: 2

FlexNetwork 5130 Series

Brand: HPE Pages: 33

Brand: ZoneVu Pages: 15

ApplianceStor 15MT

Brand: Rasilient Pages: 30

Brand: Juniper Pages: 420

Brand: IEI Technology Pages: 2

Brand: Xantech Pages: 5

Brand: Cradlepoint Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands