background image

Materials: electric heating belt, tinfoil, thermal insulation foam
Skill requirement: common technician

Procedure

Step 1 Wrap the electric heating belt around the drainpipe and water refill pipe outside

the pre-fab. module.

NO TE

● The drainpipe is pre-integrated with the electric heating belt in the outdoor unit

compartment. The outdoor part is reserved in the outdoor unit compartment and needs

to be routed onsite.

● The water refill pipe needs to be routed onsite.

Figure 8-7 Wrap the electric heating belt around the drainpipe and water refill

pipe

Step 2 Wrap the electric heating belt and pipes with tinfoil.
Step 3 Secure the temperature probe to the pipe using a cable tie.

NO TE

Secure the temperature probe to the position on the water refill and drainage pipe. The

position is the point where the electric heating belt is wrapped 50 cm long around the

water refill and drainage pipe from the water refill and drainage pipe port.

FusionDC1000A Prefabricated All-in-One Data

Center

Installation Guide (IT Scenario)

8 Installing Devices Inside the Pre-fab. Module

Issue 01 (2021-04-20)

Copyright © Huawei Technologies Co., Ltd.

73

Summary of Contents for FusionDC1000A



































































































































Reviews: