background image

FusionModule1000A20 Prefabricated All-in-One Data 
Center 
Maintenance Guide 

3 Routine Maintenance 

 

Issue 01 (2019-07-15) 

Copyright © Huawei Technologies Co., Ltd. 

21 

 

Extinguishan
t control 
panel 
batteries 

Operation 

Check Standard 

Maintenance Guide 

control panel so that 
the batteries power 
the panel. 

2.

 

Measure the battery 
voltage using a 
multimeter. 

2.

 

The battery voltage is 24±1 V 
DC. 

Hand-held fire 
extinguisher 

Check the hand-held 
fire extinguisher. 

The hand-held fire extinguisher is 
in good condition. 

Replace the hand-held fire 
extinguisher. 

The pressure pointer of the 
hand-held fire extinguisher is in 
the green zone. 

The fire extinguisher is within the 
validity period. 

 

3.4.4 Other Systems 

Table 3-10

 

Quarterly maintenance checklist for other systems 

Item 

Method 

Check Standard 

Troubleshooting 

Ventilation 
vent air filter 

Check whether the filter 
is blocked. 

The air filter is not 
blocked. 

If an air filter is slightly blocked, clean the 
air filter and reinstall it. If more than 50% of 
the meshes are blocked, replace the air filter. 

Pre-fab. 
module body 

Check the pre-fab. 
module. 

The pre-fab. 
module is clean. 

1.

 

Clean the pre-fab. module using a 
long-handled soft brush and alkaline or 
neutral detergent. 

2.

 

Wash the pre-fab. module with clean 
water. 

Pre-fab. 
module 
repainting 

Check the pre-fab. 
module exterior for 
damage or corrosion. 

The pre-fab. 
module and bases 
are free from paint 
flake-off, rust, or 
corrosion. 

Maintain or replace the rusty or damaged 
part of the pre-fab. modules. Repaint areas 
with paint flake-off or rust. 

 

Summary of Contents for FusionModule 1000A20























































































Reviews: