background image

FusionModule1000A40 IT Solution 
Maintenance Guide (2016.05, AI Version) 

6 Emergency Operations 

 

Issue 04 (2018-01-05) 

Huawei Proprietary and Confidential                                     

Copyright © Huawei Technologies Co., Ltd. 

178 

 

 

If the ATS switchover fails, manually switch the ATS to the other mains or DG supply, 
and check whether all devices are working properly. 

Step 3

 

Monitor the system running until the mains supply is stored and the system is working 
properly. 

----End 

Follow-up Procedure 

Analyze the cause of the fault, and work out and record the preventive measures. 

6.2 Emergency Operations for Circuit Breaker Tripping 

Prerequisites 

A circuit breaker has tripped. 

 

Important devices of the FusionModule1000 are powered by two power supplies. If one circuit breaker 
trips, it does not affect the operation of importance devices. However, the situation needs to be handled 
promptly to avoid jeopardizing the long term stable running of the equipment. 

Procedure 

Step 1

 

Promptly locate the control range of the circuit breaker that has tripped.   

Step 2

 

Analyze the cause of the circuit tripping and switch on the circuit breaker as soon as possible. 

----End 

Follow-up Procedure 

Analyze the cause of the fault, and work out and record the preventive measures. 

6.3 Emergency Operations for Overload 

Prerequisites 

An overload alarm is generated.   

Procedure 

Step 1

 

Locate the cable or device based on the alarm information.   

Step 2

 

Check the overloaded cable or device and locate the fault. 

 

If the cable or device is seriously overloaded, immediately power off the device and its lower-level 
devices. 

----End 

Summary of Contents for FusionModule 1000A40








































































































































































































Reviews: