background image

FusionModule1000A40 IT Solution 
Maintenance Guide (2016.05, AI Version) 

3 Maintenance 

 

Issue 04 (2018-01-05) 

Huawei Proprietary and Confidential                                     

Copyright © Huawei Technologies Co., Ltd. 

38 

 

Device 

Operation 

Check Standard 

Maintenance Guide 

Fire alarm 
bell 

Flip the key to 

Enable Control

 on 

the extinguishant 
control panel 
rightward. Press 

Silence/Sound 
Alarm

 to start or 

abort the fire alarm 
bell. Reset the key 
to 

Enable Control

 

by flipping it 
leftward.   

The alarm bell rings 
normally. The alarm 
bell rings loud and 
clear when it is 
started.   

1.

 

Check and reconnect 
cables to the fire alarm 
bell.   

2.

 

Replace the fire alarm 
bell if the fault persists. 

Warning 
sign 

Pull up the reset 
button on the 
pneumatic switch.   

The warning sign 
indicator is on.   

Replace the warning signs. 

Heat 
detector 

Heat the heat 
detector using a 
heating device.   

1.

 

If the temperature 
is below the alarm 
threshold, the 
alarm indicator 
blinks once every 
6s.   

2.

 

If the temperature 
is above the alarm 
threshold, the 
indicator turns on. 
The extinguishant 
control panel 
generates an alarm 
and triggers the 
fire alarm bell.   

Replace the heat detector. 

Smoke 
detector 

Release smoke 
onto the smoke 
detector using a 
smoke pistol.   

1.

 

If the smoke 
density is below 
the alarm 
threshold, the 
alarm indicator 
blinks once every 
6s.   

2.

 

If the smoke 
density is above 
the alarm 
threshold, the 
indicator turns on. 
The extinguishant 
control panel 
generates an alarm 
and triggers the 
fire alarm bell.   

Replace the smoke detector. 

Summary of Contents for FusionModule 1000A40








































































































































































































Reviews: