Huawei FusionModule500 User Manual Download

Page: 176 / 302

NO TE

● The initial password is Changeme after the WiFi function is enabled. The password is

valid only after you hold down the button for the first time to enable the WiFi function.

If you enable the WiFi function on the WebUI, there is no preset password.

● After the WiFi function is enabled, the password for a mobile phone to connect to the

WiFi network is Changeme. When you log in to the app using a tablet, the system

prompts you to change the password.

● After you disable the WiFi hotspot function on the WebUI and press the button again,

the WiFi function is still enabled. In this case, the WiFi password is the one you changed

last time.

● The WiFi function is disabled by default. If you need to enable the WiFi function, change

the WiFi password to ensure connection security.

● A password that has been used for a long time is more likely to be stolen or cracked.

The risk increases along with the time of use. Change the WiFi password periodically

(recommended: once half a year).

Step 4 (Optional) Enable the WiFi function on the ECC800-Pro WebUI.

1. Log in to the ECC800-Pro WebUI as an administrator.
2. Choose Monitoring > System > WiFi Converter and click WiFi

Management.

3. Set Enable WiFi to Enable and click Submit.
4. If this is the first time you enable the WiFi function, set WiFi Password and

click OK.

5. Enter the password currently used for logging in to the WebUI and click

Submit.

6. Specify WiFi SSID and WiFi Password and click Submit to change the SSID

and password.

NO TE

– If you have set a password when enabling WiFi for the first time, you do not need

to set the password again.

– The WiFi function is disabled by default. If you need to enable the WiFi function,

change the WiFi password to ensure connection security.

– A password that has been used for a long time is more likely to be stolen or

cracked. The risk increases along with the time of use. Change the WiFi password

once half a year.

7. Enter the password currently used for logging in to the WebUI and click

Submit.

Step 5 Log in to the app.

1. Start the mobile phone or pad app, choose Settings > Network Connection

on the login screen, select WiFi SSID specified on the WebUI, and enter the

value of WiFi Password specified on the WebUI for login.

2. On the login screen, choose Settings > Server IP Settings, and ensure that

the IP address is 192.168.245.10.

3. The user name and login password for the app are the same as those for the

ECC800-Pro WebUI. Specify the user name and password, and tap Login.

FusionModule500 Smart Mini Data Center

User Manual

5 Power-On Commissioning

Issue 02 (2020-12-25)

166

Summary of Contents for FusionModule500















































































































































































































































































































Search results

Summary of Contents for FusionModule500

Reviews:

Related manuals for FusionModule500

Brands by name

Popular brands

Huawei FusionModule500, User Manual

Search results

Summary of Contents for FusionModule500

Reviews:

Related manuals for FusionModule500

Brands by name

Popular brands