Huawei FusionModule500 User Manual Download

Page: 259 / 302

Maintenance

Area

Maintenance

Item

Operation

Expected Result Troubleshootin

UPS

Operating

environment

● Ambient

temperature:

0–40°C

● Humidity:

0%–95% RH

(non-

condensing)

● If the

temperature

or humidity

is abnormal,

check the

smart

cooling

product

status.

● If the input

voltage is

abnormal,

check the

power grid

status and

input cable

connection.

LCD

According to the

status icons on

the LCD, all units

are operating

properly. No

fault or alarm

information is

found in the

active and

historical alarm

records.

If an alarm is

present, rectify

the fault by

checking the

device status

and parameters.

Cleanliness

Wipe the cabinet

surface using a

white paper and

the paper does

not turn black.

Remove the

dust, especially

from the air

filter on the

front door, or

replace the air

filter.

Parameter

configuration

The

configuration of

the output

voltage grade,

frequency,

number of

batteries, and

battery capacity

meets

requirements.

Reset the

parameters.

FusionModule500 Smart Mini Data Center

User Manual

6 O&M

Issue 02 (2020-12-25)

249

Summary of Contents for FusionModule500















































































































































































































































































































Search results

Summary of Contents for FusionModule500

Reviews:

Related manuals for FusionModule500

Brands by name

Popular brands

Huawei FusionModule500, User Manual

Search results

Summary of Contents for FusionModule500

Reviews:

Related manuals for FusionModule500

Brands by name

Popular brands