Huawei FusionModule500 User Manual Download

Page: 273 / 302

Component

Alarm Name

Alarm

Severit

Possible Cause

Measures

Inverter fault

Critical

The inverter output

short-circuits.

Eliminate the short

circuit at the output

port cable connection,

and then power on and

start the inverter again.

If the fault persists,

contact Huawei

technical support.

Output short

circuit

NOTE

The system

immediately

disconnects the

power output.

Critical

The load or cable is

short-circuited.

Locate and rectify the

short circuit.

Intelligent

lithium

battery

monitoring

system

Communication

Failure

Critical

The network cable

communication is

interrupted.

Check the cable

connection to the smart

ETH gateway.

BCB Tripping

Critical

● The battery has

discharged to the

end-of-discharge

(EOD) threshold.

● The battery circuit

breaker (BCB) box is

manually

disconnected.

● There is a security

risk in the battery

loop.

Identify the alarm

cause, rectify the fault,

and switch on the BCB

box.

Single Batt.

terminal off

Critical

● A battery terminal

screw is not

tightened.

● The battery terminal

is not properly

connected to the

connector.

● Check that battery

terminal screws are

tightened.

● Check that battery

terminals are

properly connected

to connectors.

FusionModule500 Smart Mini Data Center

User Manual

6 O&M

Issue 02 (2020-12-25)

263

Summary of Contents for FusionModule500















































































































































































































































































































Search results

Summary of Contents for FusionModule500

Reviews:

Related manuals for FusionModule500

Brands by name

Popular brands

Huawei FusionModule500, User Manual

Search results

Summary of Contents for FusionModule500

Reviews:

Related manuals for FusionModule500

Brands by name

Popular brands