Huawei FusionModule500 User Manual Download

Page: 54 / 302

Table 3-27 RJ45 port pin definitions

Pin

Description

Pin1 or Pin 4

Pin2 or Pin 5

Pin3

V+

Pin6

V-

Pin7

Reserved

Table 3-28 T/H sensor specifications

Item

Specifications

Temperature measuring range

–20°C to +70°C

Temperature accuracy

±1°C

Humidity measuring range

5%–95% RH

Humidity precision

±5% RH (25°C, 20%–80% RH)

Operating temperature

–20°C to +70°C

Operating voltage

9–16 V DC

Storage temperature

–40°C to +70°C

Output

RS485

3.4.3.2.4 Smoke Detector

A smoke detector detects smoke around cabinets.

Figure 3-15 Smoke detector

FusionModule500 Smart Mini Data Center

User Manual

3 System Architecture

Issue 02 (2020-12-25)

Summary of Contents for FusionModule500















































































































































































































































































































Search results

Summary of Contents for FusionModule500

Reviews:

Related manuals for FusionModule500

Brands by name

Popular brands

Huawei FusionModule500, User Manual

Search results

Summary of Contents for FusionModule500

Reviews:

Related manuals for FusionModule500

Brands by name

Popular brands