Huawei FusionModule500 User Manual Download

Page: 181 / 302

Path

Parameter

Setting

devices are

displayed.

Communicati

ons Port

Select COM4 from the drop-down list box.

NOTE

The setting example indicates that the

UPS2000G is connected to the COM4 port on

the ECC800-Pro. If the UPS2000G is connected

to another port, enter the number of the

connected port.

Device

Address

In this example, Device Address is set to 1.

During actual configuration, set the device

address for the UPS2000G-L based on the

actual situation.

3. Click Test Connect to check whether the UPS2000G-L connects to the

ECC800-Pro properly.
–

If the connection succeeds, click Confirm. The connected devices are

displayed in the Number of connected devices list.

–

If the connection fails, check whether the device is properly connected to

the ECC800-Pro, whether the device and ECC800-Pro are running

properly, and whether the parameter settings are consistent with the

device parameters.

----End

5.3.8 Commissioning Sensors

5.3.8.1 Setting and Adding a Smoke Detector (Connected to an AI/DI Port on

the ECC800-Pro)

If a smoke detector is installed, perform the following steps to configure it.

Context

If the detector is prefabricated, only check its settings.

Procedure

Step 1 Set smoke detector parameters.

1. Log in to the ECC800-Pro WebUI as an administrator.
2. Choose System Settings > Signal Name Modify. The Batch Signal

Configuration tab page is displayed.

3. Set Device type to ECC800, set Device name to ECC800, and click OK.
4. On the query result tab page, set the new signal name of AI/DI_1 to Smoke

and click Submit.

5. Choose Monitoring > System > ECC800 > Running Parameters > AI/DI_1

Port Settings.

6. Set Smoke sensor to Enable and click Submit.

FusionModule500 Smart Mini Data Center

User Manual

5 Power-On Commissioning

Issue 02 (2020-12-25)

171

Summary of Contents for FusionModule500















































































































































































































































































































Search results

Summary of Contents for FusionModule500

Reviews:

Related manuals for FusionModule500

Brands by name

Popular brands

Huawei FusionModule500, User Manual

Search results

Summary of Contents for FusionModule500

Reviews:

Related manuals for FusionModule500

Brands by name

Popular brands