Huawei FusionModule500 User Manual Download

Page: 33 / 302

NO TE

● The RS485 port supports only the Modbus RTU protocol.
● a: The USB port supports the serial port communication protocol. The USB port can be

used to export logs and send serial port commissioning commands.

● b: The RS232 port supports the serial port communication protocol. The RS232 port can

be used to export logs, send serial port commissioning commands, and upgrade the UPS

main power program online.

Table 3-2 6 kVA UPS technical specifications

Item

Specifications

Rated capacity

6 kVA

Number of phases

Input power factor

≥ 0.99

Output power factor

≥ 0.9

Rated input voltage

220 V AC/230 V AC/240 V AC

Input voltage range

110–280 V AC; < 176 V AC: derated; 110 V AC: 50%

load

Rated input frequency

50 Hz/60 Hz

Input frequency range

● 50 Hz: 46–54 Hz
● 60 Hz: 56–64 Hz

Output frequency range 50 Hz±0.5%

Peak efficiency

Normal mode: 93% (online mode)
Normal mode: 90%

Dimensions (H x W x

131 mm x 438 mm x 480 mm

Weight

15 kg

3.2.3 Power Distribution Subrack

Table 3-3 Technical specifications

Item

Specifications

Maximum input current

63 A

Number of phases

Input frequency

50 Hz/60 Hz

Input voltage

220 V

FusionModule500 Smart Mini Data Center

User Manual

3 System Architecture

Issue 02 (2020-12-25)

Summary of Contents for FusionModule500















































































































































































































































































































Search results

Summary of Contents for FusionModule500

Reviews:

Related manuals for FusionModule500

Brands by name

Popular brands

Huawei FusionModule500, User Manual

Search results

Summary of Contents for FusionModule500

Reviews:

Related manuals for FusionModule500

Brands by name

Popular brands