background image

23

1. Log in to the WebUI of the ECC controller as an administrator and choose 

Monitoring

Air 

Conditioner > NetCol5000-A0101 

to enter the settings page.

2. Click 

Controls

Control Information

, choose 

On/off status on EMS 

ON

, and then click 

Submit

.

3. On the 

Controls

Control Information 

page, choose 

Diagnostic Mode 

Enable 

and click 

Submit

.

4. Choose 

Running Parameters 

Diagnostic Mode Parameters, 

on the 

Diagnostic Mode 

Parameters 

page, set 

EEV Opening 

of the electronic expansion valve to 

300step

, set 

Liquid 

Solenoid Val t

Open 

and click 

Submit

, then keep that for 30s to allow for the positive 

pressure inside the refrigerant pipe of the indoor unit.

5. (Optional) Choose 

Running Parameters 

Diagnostic Mode Parameters

. Then choose 

Elec

heater manual control 

Open

and click 

Submit

.

Check that the indoor fan operates properly without alarms.

If hot air blows out from the air exhaust vent of the fan after a period of time, the electric 

heater runs properly. In this case, choose 

Elec heater manual control 

Closed

and then 

click 

Submit

.

6. (Optional) Commission the wet film humidifier.

On the 

Diagnostic Mode Parameters 

page, set 

Inlet solenoid man ctrl 

to 

Open

and 

click 

Submit

. Check that the water inlet pipe does not leak and the humidifier float works 

properly. Choose 

Inlet solenoid man ctrl 

Closed

and then click 

Submit

Choose 

Humidifier film man ctrl 

Open

and click 

Submit

. Then choose 

Running Info 

Humidifier Information

Humidifier pump ctrl 

and check that the humidifier water 

pump is open and water flows down along the wet film. Choose 

Humidifier film man 

ctrl 

Closed

and then click 

Submit

.

7. Commission the condensate pump. Lift the low liquid level detector. After 5 seconds, when 

you hear the water pump operating sound, lay down the low liquid level detector. (It is 

normal if a pump alarm is generated when there is no water in the pan. The pump generates 

this alarm for self-protection and this alarm needs to be cleared manually.) 

8. Commission the compressor. If required charge refrigerant, perform the following steps.

Summary of Contents for NetCol5000-A011





























Reviews: