Huawei NetCol5000-C030H90D0 User Manual Download

Page: 15 / 206

●

Ensure that the equipment room provides good heat insulation, and the walls

and floor are dampproof.

●

Install a rat guard at the door of the equipment room.

Installation at Heights

●

Working at heights refers to operations that are performed at least 2 meters

above the ground.

●

Do not work at heights if the steel pipes are wet or other potential danger

exists. After the preceding conditions no longer exist, the safety director and

relevant technical personnel need to check the involved equipment. Operators

can begin working only after obtaining consent.

●

When working at heights, comply with local relevant laws and regulations.

●

Only trained and qualified personnel are allowed to work at heights.

●

Before working at heights, check the climbing tools and safety gears such as

safety helmets, safety belts, ladders, springboards, scaffolding, and lifting

equipment. If they do not meet the requirements, take corrective measures or

disallow working at heights.

●

Wear personal protective equipment such as the safety helmet and safety belt

or waist rope and fasten it to a solid structure. Do not mount it on an

insecure moveable object or metal object with sharp edges. Make sure that

the hooks will not slide off.

●

Set a restricted area and eye-catching signs for working at heights to warn

away irrelevant personnel.

●

Carry the operation machinery and tools properly to prevent them from

falling off and causing injuries.

●

Personnel involving working at heights are not allowed to throw objects from

the height to the ground, or vice versa. Objects should be transported by

tough slings, hanging baskets, highline trolleys, or cranes.

●

Ensure that guard rails and warning signs are set at the edges and openings

of the area involving working at heights to prevent falls.

●

Do not pile up scaffolding, springboards, or other sundries on the ground

under the area involving working at heights. Do not allow people to stay or

pass under the area involving working at heights.

●

Inspect the scaffolding, springboards, and workbenches used for working at

heights in advance to ensure that their structures are solid and not

overloaded.

●

Any violations must be promptly pointed out by the site manager or safety

supervisor and the involved personnel should be prompted for correction.

Personnel who fail to stop violations will be forbidden from working.

1.5 Mechanical Safety

Hoisting Devices

●

Do not walk under hoisted objects.

●

Only trained and qualified personnel should perform hoisting operations.

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual (2019)

1 Safety Information

Issue 03 (2020-08-30)

Summary of Contents for NetCol5000-C030H90D0















































































































































































































Search results

Summary of Contents for NetCol5000-C030H90D0

Reviews:

Related manuals for NetCol5000-C030H90D0

Brands by name

Popular brands

Huawei NetCol5000-C030H90D0, User Manual

Search results

Summary of Contents for NetCol5000-C030H90D0

Reviews:

Related manuals for NetCol5000-C030H90D0

Brands by name

Popular brands