background image

Appearance 

PDC is short for power distribution cabinet. 

PDU is short for power distribution unit. 

UPS is short for uninterruptible power system. 

PDU Model 

PDC-0038V4ACIOA-V2 

Applicable UPS 

UPS2000-G-3KRTL/6KRTL-V2 

Weight 

15 kg 

Dimensions 

 (H x W x D) 

130 mm x 430 mm x 585 mm 

1. UPS 1 mains input 

circuit breaker 

2. UPS 2 mains input circuit 

breaker 

3. UPS 1 bypass input circuit 

breaker 

4. UPS 2 bypass input circuit 

breaker 

5. UPS 1 output circuit 

breaker 

6. UPS 2 output circuit 

breaker 

7. Maintenance bypass circuit 

breaker 

8. Maintenance bypass circuit 

breaker cover 

PDC-0038V4ACIOA-V2 

Front panel (under the cover) 

Rear panel 

10 

11 

12 

13 

14 

15 

16 

1. Maintenance bypass 

ports 

2. Dual in-line package (DIP) 

switch 

3. Control area network (CAN) 

communications ports

 

4. Output ports 

5. Bypass input ports 

6. Mains input ports 

7. Output socket group 1 (250 V 

AC, 15 A, disabled in the case     

of 110 V output) 

8. Output socket group 1 

fuses (250 V AC, 15 A) 

9. Output socket group 2 

fuses (250 V AC, 10 A) 

10. Output socket group 2 

(250 V AC, 10 A, disabled in 

the case of 110 V output) 

11. UPS 1 mains input port 

12. UPS 2 mains input port 

13. UPS 1 bypass input 

port 

14. UPS 2 bypass input port 

15. UPS 1 output port 

16. UPS 2 output port 

Summary of Contents for PDC-0038V4ACIOA-V2












Reviews: