Huawei PDC-0038V4ACIOA Quick Installation Manual Download

Page: 7 / 12

After the PDU is tower-mounted, seal the four screw holes on the top with rubber plugs that are delivered with the PDU.

Install two support bases for each group of devices. Place the support bases on the floor, determine the distance (greater
than or equal to 280 mm) between the support bases, place devices on the support bases, and secure them.

Assemble support bases. When you assemble two support bases, align connecting buckles with holes and insert the

buckles vertically, as shown in the following figure.

Support

base

Connecting

buckle

Components

installed

between

support

bases

3 U battery packs

3 U UPSs

3 U PDC-

0038V4ACIOA

Rubber plugs

Cable Installation

Remove the front panel from the PDU and open the circuit breakers.

OFF

Summary of Contents for PDC-0038V4ACIOA













Search results

Summary of Contents for PDC-0038V4ACIOA

Reviews:

Related manuals for PDC-0038V4ACIOA

Brands by name

Popular brands

Huawei PDC-0038V4ACIOA, Quick Installation Manual

Search results

Summary of Contents for PDC-0038V4ACIOA

Reviews:

Related manuals for PDC-0038V4ACIOA

Brands by name

Popular brands