background image

Check Item

Expected Result

Troubleshooting

Battery

appearance

1. The surface is clean and tidy

without stains.

2. The battery terminals are

intact.

3. Batteries are free from

damage and cracks.

4. Batteries are free from acid

or electrolyte leakage.

5. Batteries are not deformed

or bulged.

If an exception occurs, contact

technical support.

 

Table 7-2 Quarterly maintenance

Check Item

Expected Result

Troubleshooting

Dust on the air

filter

No obvious dust is

accumulated.

Clean the component if

there is heavy dust or

replace the component if it

is damaged.

Shallow

discharge test

(recommende

d).

Conduct a shallow discharge

test when the UPS is backed up

to verify that the batteries can

discharge normally.

1. Locate the fault cause. (If

a fault alarm is

generated, handle it

according to the 

UPS5000

& SmartLi Alarm

Reference

.)

2. If the fault persists,

contact technical support.

 

Table 7-3 Annual maintenance

Check Item

Expected Result

Troubleshooting

Grounding

Ground cables are connected

securely.

Tighten the screws.

Power cables

and terminals

Screws are tightened. The

insulation layers of cables are

intact and terminals are free

from black marks and noticeable

sparks.

Replace cables or secure

output terminals.

Capacity test

When the UPS is backed up,

discharge a battery to the

undervoltage alarm threshold to

refresh the capacity of the

battery.

1. Locate the fault cause.
2. If the fault persists,

contact technical support.

SmartLi 2.0

User Manual

7 Routine Maintenance

Issue 09 (2022-01-30)

Copyright © Huawei Technologies Co., Ltd.

131

Summary of Contents for SmartLi 2.0














































































































































































Reviews: