background image

4.2.1 Installing a Fire Extinguisher Cylinder

Procedure

Step 1 Remove the rear panel of the cabinet.

Step 2 Observe the pressure gauge on the fire extinguisher cylinder.

If the pointer reading is 0 MPa, the fire extinguisher cylinder is empty.

Perform steps 3–10 to fill extinguishant onsite.

If the pointer reading is greater than 1.1 MPa, the fire extinguisher cylinder is

filled with extinguishant. In this case, perform steps 8–10.

Step 3 Remove the fire extinguisher cylinder and dry contact cable.

1. Remove the dry contact cable from the fire extinguisher cylinder.
2. Remove the fire extinguisher cylinder fastener.
3. Take out the fire extinguisher cylinder.

Figure 4-2 Removing the fire extinguisher cylinder

Step 4 Check the fire extinguisher cylinder and all components for any damage, abrasion,

or corrosion. If there is any visible abrasion or corrosion, replace the damaged

components and all corroded components.

Step 5 Send the fire extinguisher cylinder to a station to refill extinguishant.

Heptafluoropropane or perfluorohexanone is recommended. The required amount

is 3 kg.

NO TICE

● In the process of assembling and filling, ensure that the valve, container, and

other parts are clean and not polluted.

● The internal impurities of the fire extinguisher cylinder have been cleaned and

the container valve has been sealed. Do not remove the container valve and its

components. For other operations, see the related filling specifications.

SmartLi 2.0

User Manual

4 Installation

Issue 09 (2022-01-30)

Copyright © Huawei Technologies Co., Ltd.

43

Summary of Contents for SmartLi 2.0














































































































































































Reviews: