background image

4

 Configuration (Command Line Mode) 

U-SYS IAD101H/102H/104H Integrated Access Device 

Quick Start 

 

10 

Huawei Proprietary and Confidential        

Copyright © Huawei Technologies Co., Ltd. 

Issue 02 (2011-02-09) 

TERMINAL(config)#

terminal timeout 255

 

Step 2

 

Configure the IP address of the IAD. There are three methods for obtaining the IP 
address, that is, Static IP address, DHCP and PPPoE. By default, the IAD obtains an IP 
address through DHCP automatically after being connected to the network. You can 
choose another method for obtaining the IP address: 

z

 

Run 

ipaddress static ip-address subnet-mask default-gateway

 to set a fixed IP 

address. 

z

 

Run 

ipaddress dhcp

 to obtain an IP address through DHCP. (A DHCP server is 

required.) 

z

 

Run 

pppoe username user-name password password

 to set the PPPoE user name 

and password, and then run 

ipaddress pppoe

 to obtain an IP address through 

PPPoE. (A PPPoE server is required, and the user name and password need to be 
set as the same as that on the PPPoE server.) 

You can run 

display ipaddress

 to view the IP address of the IAD. 

 

Changing the IP address may disconnect the Telnet connection. Then, you should establish 
the Telnet connection again with the new IP address. 

Step 3

 

Set the registered domain. 
Run 

mgcp mg-domain-name name

. The 

name

 of the IAD, which is registered on the 

MGC server, is iad001. 

TERMINAL(config)#

mgcp mg-domain-name iad001

 

Step 4

 

Run the 

mgcp mgc index address ip-address

 command to configure the MGC server. 

For the MGC server, the index is 1, the IP address is 191.168.10.20. 

TERMINAL(config)#

mgcp mgc 1 address 191.168.10.20

 

 

You can set the 

index 

  to 2 to configure a backup MGC server. The IAD registers to the 

MGC server of 

index 

  1; if the registration fails, the IAD registers to the MGC server of 

index 

  2 to ensure the normal running of the service. 

Run 

display mgcp attribute

 to view the configuration result. 

Step 5

 

(Optional) Synchronize the system time with the SNTP server, giving the log and alarm 
records accurate time for reference. 
Run 

sntp server address ip-address

 to set the IP address of a SNTP server, and then 

run 

sntp interval <0-3600>

 to set the synchronization interval and run 

sntp time-zone 

{

<

0-13

> |

 -

 <

1-12

>} to set the time zone (for example, the Bejing time zone is +8, 

run 

sntp time-zone + 8

). 

z

 

You can set the SNTP server to a PC on which the Windows Time service is 
enabled. The PC must work continuously. To check whether the Window Time 
service is enabled on a PC, choose 

Control Panel

 > 

Management Tools

 > 

Services

z

 

If the MGC server can function as an SNTP server, you can set the SNTP server to 
the MGC server. 

You can run 

display sntp

 to view the status of the SNTP server. 

 

Summary of Contents for U-SYS IAD101H




















Reviews: