background image

4

 Configuration (Command Line Mode) 

U-SYS IAD101H/102H/104H Integrated Access Device 

Quick Start 

 

Huawei Proprietary and Confidential        

Copyright © Huawei Technologies Co., Ltd. 

Issue 02 (2011-02-09) 

 

4

Configuration (Command Line Mode) 

 

You can configure the data of the IAD by using the command line. 

GN/IP PBX

 IAD

4.6  Setting the UCEMS Parameters

4.1 Lo

 the 

 

feature. You can enter a question mark (?) to obtain help and press Spacebar to 

ete a command name. 

u

Step 1

 

e IP address segment as “192.168.100.1” (for example, 

Step 2

 

nk space + the actual IP address of the 

click 

OK

, as shown below. 

4.1  Logging In Through Telnet
4.2  IAD(SIP) Accessing NGN/IP PBX
4.3  IAD(MGCP) Accessing N
4.4  IAD(SIP) Accessing IMS
4.5    Accessing Network Through the

gging In Through Telnet 

The LAN port IP address of the IAD101H/102H/104H is 192.168.100.1 by default. 
You can access the command line interface (CLI) of the IAD through Telnet.For
IAD104H, serial port is an alternative access. The CLI includes an interactive Help

compl

Proced re 

Connect your PC to the LAN port of the IAD by a network cable, and then set the IP 
address of your PC to the sam
192.168.100.2), and the subnet mask to 255.255.255.0. Ensure that you can ping 

192.168.100.1

 successfully. 

Choose 

Start 

 > 

Run

, and enter “telnet” + a bla

IAD network port in the 

Run

 dialog box. Then 

 

 
After a conn

Step 3

 

ection is established, enter user name 

root

 and password 

admin

 to log in 

to the IAD. 

Summary of Contents for U-SYS IAD101H




















Reviews: