manualshive.com logo in svg

Huawei UA5000, Manual

The Huawei UA5000 is a versatile and reliable telecommunications device. Enhance your understanding and maximize the device's potential by downloading the comprehensive user manual for free on our website, ensuring seamless usage of this cutting-edge product. Visit 88.208.23.73:8080 to download the manual and unlock its full capabilities.

Share
Download
background image

     2     -                     1     |   3     -                     1        
     4     -                     1     |   5     -                     1        
     6     -                     1     |   7     -                     1        
     8     -                     1     |   9     -                     1        
     10    -                     1     |   11    -                     1        
     12    -                     1     |   13    -                     1        
     14    -                     1     |   15    -                     1        
     16    -                     1     |   17    -                     1        
     18    -                     1     |   19    -                     1        
     20    -                     1     |   21    -                     1        
  ----------------------------------------------------------------------------  
  COM ID  Command BaudRate  DataLength  StopLength  ParityType                  
    0       -       -         -           -         -                           
    1       -       -         -           -         -                           
  PowerNumber  : 0              PowerType  : -                                  
  ----------------------------------------------------------------------------  

The results show that certain monitoring parameters, such as temperature, humidity, door
status, and MDF, have been configured automatically in the system. Other monitoring
parameters, however, need to be configured manually.

4.

Configure the analog parameters.

huawei(config-if-h303esc-0)#

esc analog 0 alarm-upper-limit 50 alarm-lower-

limit 10

huawei(config-if-h303esc-0)#

esc analog 1 alarm-upper-limit 80 alarm-lower-

limit 5

huawei(config-if-h303esc-0)#

esc analog 4 alarm-upper-limit 75 alarm-lower-

limit 45 name Supply_Voltage sensor-type 0:voltage analog-alarm 3 unit Volt

5.

Configure the digital parameters.

huawei(config-if-h303esc-0)#

esc digital 2 available-level low-level digital-

alarm 13 name fan1

huawei(config-if-h303esc-0)#

esc digital 3 available-level low-level digital-

alarm 13 name fan2

huawei(config-if-h303esc-0)#

esc digital 4 available-level low-level digital-

alarm 13 name fan3

huawei(config-if-h303esc-0)#

esc digital 5 available-level low-level digital-

alarm 13 name fan4

6.

Query the environment information, and confirm that the environment monitoring
functions are normal and the door status alarm other than alarms for other monitoring
parameters is generated.

huawei(config-if-h303esc-0)#

display esc environment info

  EMU ID: 0                             ESC environment state                   
  FAN control mode :Auto  FAN run state: Open                                   
  ---------------------------Analog environment info--------------------------  
  ID Name                State    Value   AlmUpper   AlmLower   Unit            
  0  Temperature         Normal   29.00      50         10        C             
  1  Humidity            Normal   30.98      80         5        %R.H.          
  2  -                   Normal   -128.00    127        -128     -              
  3  -                   Normal   -128.00    127        -128     -              
  4  Supply_Voltage      Normal   53.50      75         45       -              
  5                      Normal   -128.00    127        -128     -              
  6  -                   Normal   -128.00    127        -128     -              
  7  -                   Normal   -128.00    127        -128     -              
  ---------------------------Digital environment 
info---------------------------
  ID Name                State  Value |ID Name                State  Value      
  0  Wiring              Normal 1     |1  Door0               Alarm  1          
  2  fan1                Normal 0     |3  fan2                Normal 0          
  4  fan3                Normal 0     |5  fan4                Normal 0          
  6  -                   Normal 1     |7  -                   Normal 1          
  8  -                   Normal 1     |9  -                   Normal 1          
  10 -                   Normal 1     |11 -                   Normal 1          
  12 -                   Normal 1     |13 -                   Normal 1          
  14 -                   Normal 1     |15 -                   Normal 1          
  16 -                   Normal 1     |17 -                   Normal 1          
  18 -                   Normal 1     |19 -                   Normal 1          
  20 -                   Normal 1     |21 -                   Normal 1          
  ----------------------------------------------------------------------------  

UA5000 Universal Access Unit
Environment Monitoring

3 H303ESC Monitoring Solution

Issue 01 (2012-08-17)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

22

Summary of Contents for UA5000


















































































































































































































Reviews:

No comments

Related manuals for UA5000

Abocom ET-UW100 User Manual preview
ET-UW100
Brand: Abocom Pages: 14
PROLiNK PRT7010L Quick Installation Manual preview
PRT7010L
Brand: PROLiNK Pages: 28
Kasda KW9621B Manual preview
KW9621B
Brand: Kasda Pages: 42
Andersson WSR 2.0 User Manual preview
WSR 2.0
Brand: Andersson Pages: 47
2N LiftGate User Manual preview
LiftGate
Brand: 2N Pages: 82
Advantech WLAN-9100 Manual preview
WLAN-9100
Brand: Advantech Pages: 46
u-blox LILY-W1 Series System Integration Manual preview
LILY-W1 Series
Brand: u-blox Pages: 64
Air Live WMM-3000R Quick Setup Manual preview
WMM-3000R
Brand: Air Live Pages: 51
EnGenius ECB-3220 User Manual preview
ECB-3220
Brand: EnGenius Pages: 51
AmbiCom WL1100B-AP User Manual preview
WL1100B-AP
Brand: AmbiCom Pages: 27
Delta PICOSTATION-M2-HP User Manual preview
PICOSTATION-M2-HP
Brand: Delta Pages: 5
Vertex Wireless VW300 series User Manual preview
VW300 series
Brand: Vertex Wireless Pages: 54
Hunter A2C-WIFI Installation preview
A2C-WIFI
Brand: Hunter Pages: 5
Zcom SP420 Series Quick Start Manual preview
SP420 Series
Brand: Zcom Pages: 10
Browan L0001 User Manual preview
L0001
Brand: Browan Pages: 21
OBERON H-bar 1015 Series Installation Manual preview
H-bar 1015 Series
Brand: OBERON Pages: 3
CommScope Ruckus Unleashed R650p Quick Setup Manual preview
Ruckus Unleashed R650p
Brand: CommScope Pages: 7
Sitecom DC-202V4 Quick Installation Manual preview
DC-202V4
Brand: Sitecom Pages: 8

Brands by name

Popular brands

Load more brands