manualshive.com logo in svg

Huawei UA5000, Manual

The Huawei UA5000 is a versatile and reliable telecommunications device. Enhance your understanding and maximize the device's potential by downloading the comprehensive user manual for free on our website, ensuring seamless usage of this cutting-edge product. Visit 88.208.23.73:8080 to download the manual and unlock its full capabilities.

Share
Download
background image

----------------------------------------------------------------------------
COM ID  Command BaudRate  DataLength  StopLength  ParityType
  0       -       -         -           -         -
  1       -       -         -           -         -
PowerNumber  : 0              PowerType  : -
Battery off permission: Permit    Battery off voltage: 43.2V
Battery0 capacity: 100A   Battery1 capacity: 100A    Equalizing time: 60days
----------------------------------------------------------------------------

The results show that certain monitoring parameters, such as temperature, voltage, door
status, and MDF, have been configured automatically in the system. Other monitoring
parameters, however, need to be configured manually.

4.

Configure the analog parameters.

huawei(config-if-h304esc-0)#

esc analog 0 alarm-upper-limit 50 alarm-lower-

limit 5

huawei(config-if-h304esc-0)#

esc analog 5 alarm-upper-limit 80 alarm-lower-

limit 0 name Humidity sensor-type 0:voltage analog-alarm 2 unit %RH

5.

Configure the digital parameters.

huawei(config-if-h304esc-0)#

esc digital 2 available-level low-level name SPD1

huawei(config-if-h304esc-0)#

esc digital 3 available-level low-level name SPD2

huawei(config-if-h304esc-0)#

esc digital 4 available-level low-level name SW1

huawei(config-if-h304esc-0)#

esc digital 5 available-level low-level name SW2

huawei(config-if-h304esc-0)#

esc digital 6 available-level low-level name SW3

huawei(config-if-h304esc-0)#

esc digital 8 available-level low-level name fan1

huawei(config-if-h304esc-0)#

esc digital 9 available-level low-level name fan2

huawei(config-if-h304esc-0)#

esc digital 10 available-level low-level name fan3

huawei(config-if-h304esc-0)#

esc digital 11 available-level low-level name fan4

6.

Query the environment information, and confirm that the environment monitoring
functions are normal and the door status alarm other than alarms for other monitoring
parameters is generated.

huawei(config-if-h304esc-0)#

display esc environment info

  EMU ID: 0                             ESC environment state                   
  FAN control mode :Auto  FAN run state: Close  Battery charge state: Floating  
  ---------------------------Analog environment info--------------------------
  ID Name                State    Value   AlmUpper   AlmLower   Unit
  0  Temperature         Normal   29.00      55         5        C
  1  -                   Normal   0.00       127        -128     -
  2  -                   Normal   0.00       127        -128     -
  3  -                   Normal   -128.00    127        -128     -
  4  Supply_Voltage      Normal   52.73      75         45       Volt
  5  Humidity            Normal   30.98      80         0        -
  6  -                   Normal   -128.00    127        -128     -
  7  -                   Normal   -128.00    127        -128     - 
  ---------------------------Digital environment info
  ID Name                State  Value |ID Name                State  Value
  0  Wiring              Normal 1     |1  Door0               Alarm  1
  2  SPD1                Normal 0     |3  SPD2                Normal 0
  4  SW1                 Normal 0     |5  SW2                 Normal 0
  6  SW3                 Normal 0     |7  -                   Normal 1
  8  fan1                Normal 0     |9  fan2                Normal 0
  10 fan3                Normal 0     |11 fan4                Normal 0
  12 -                   Normal 1     |13 -                   Normal 1
  14 -                   Normal 1     |15 -                   Normal 1
  16 -                   Normal 1     |17 -                   Normal 1
  18 -                   Normal 1     |19 -                   Normal 1
  20 -                   Normal 1     |21 -                   Normal 1
  ----------------------------------------------------------------------------

NOTE

Door status alarm "Door0" is generated because the door is open. At this time, if you turn on the
buzzer on the front panel of the H304ESC board, the buzzer generates a buzzing tone.

7.

Save the data.

huawei(config-if-h304esc-0)#

quit

huawei(config)#

save

UA5000 Universal Access Unit
Environment Monitoring

4 H304ESC Monitoring Solution

Issue 01 (2012-08-17)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

42

Summary of Contents for UA5000


















































































































































































































Reviews:

No comments

Related manuals for UA5000

AirM2M A6501 User Manual preview
A6501
Brand: AirM2M Pages: 64
Meru Networks AP822 Installation Manual preview
AP822
Brand: Meru Networks Pages: 66
LTE inadria LC300 Quick Start Manual preview
inadria LC300
Brand: LTE Pages: 8
Alfa Network AWAP05O User Manual preview
AWAP05O
Brand: Alfa Network Pages: 226
BenQ DEY21 User Manual preview
DEY21
Brand: BenQ Pages: 15
Verizon Jetpack MiFi 4510L User Manual preview
Jetpack MiFi 4510L
Brand: Verizon Pages: 88
Abocom AP700C User Manual preview
AP700C
Brand: Abocom Pages: 37
Airlink101 AR580W3G User Manual preview
AR580W3G
Brand: Airlink101 Pages: 134
ICP DAS USA WF-2015 User Manual preview
WF-2015
Brand: ICP DAS USA Pages: 61
Topcom BR 104 Quick Installation Manual preview
BR 104
Brand: Topcom Pages: 45
Loopcomm LP-2026 User Manual preview
LP-2026
Brand: Loopcomm Pages: 40
4IPNET EAP717 Quick Installation Manual preview
EAP717
Brand: 4IPNET Pages: 15
4IPNET EAP700 Quick Installation Manual preview
EAP700
Brand: 4IPNET Pages: 20
Trust 13511 User Manual preview
13511
Brand: Trust Pages: 19
EnGenius ECB300 Quick Installation Manual preview
ECB300
Brand: EnGenius Pages: 2
EnGenius ECB150 Quick Installation Manual preview
ECB150
Brand: EnGenius Pages: 2
3e Technologies International AirGuard 3e-525C-2 User Manual preview
AirGuard 3e-525C-2
Brand: 3e Technologies International Pages: 80
3e Technologies International 3e-531AP User Manual preview
3e-531AP
Brand: 3e Technologies International Pages: 104

Brands by name

Popular brands

Load more brands