manualshive.com logo in svg

Huawei UA5000, Manual

The Huawei UA5000 is a versatile and reliable telecommunications device. Enhance your understanding and maximize the device's potential by downloading the comprehensive user manual for free on our website, ensuring seamless usage of this cutting-edge product. Visit 88.208.23.73:8080 to download the manual and unlock its full capabilities.

Share
Download
background image

To...

Run the Command...

Configure the digital parameters

esc digital

IDs of user-defined alarms in the digital parameters: IDs
1-20 are reserved alarm IDs in the system (1:
AC_voltage; 2: AC_switch; 3: Battery_voltage; 4:
Battery_fuse; 5: Load_fuse; 6: Rectifier; 7: DC_power;
8: Cupboard_door; 9: Room_door; 10: Window; 11:
Theft; 12: Wiring; 13: Fan; 14: Fire; 15: Fog; 16: Water;
17: Diesel; 18: Smell 19: Air_conditioner; 20: SPD), and
IDs 21-52 are alarm IDs allocated to other user-defined
alarms by users.

 

The following considers the configuration in the M200 cabinet as an example to describe the
process of configuring the environment monitoring parameters of the ESCM.

1.

Log in to the UA5000 through the maintenance terminal and add an EMU.

huawei(config)#

emu add 0 MiniESC 0 30 rs232 MiniESC

2.

Enter the ESCM configuration mode and query the default analog and digital parameters.

huawei(config)#

display emu 0

  EMU ID: 0                                                                     
  ----------------------------------------------------------------------------  
  EMU name    : MiniESC                                                         
  EMU type    : MiniESC                                                         
  Used or not : Used                                                            
  EMU state   : Normal                                                          
  Frame ID    : 0                                                               
  Subnode     : 30                                                              
  COM port    : RS232                                                           

3.

Enter the ESCM configuration mode and query the default analog and digital parameters.

huawei(config)#

interface emu 0

huawei(config-if-MiniESC-0)#

display esc system parameter

                                                                                
  EMU ID: 0                             ESC system parameter                    
  ----------------------------------------------------------------------------  
  FAN run mode: Auto  Auto open temperature: 45 C  Auto close temperature: 30 
C 
  AnalogID Name            AlmUpper AlmLower TestHigh  TestLow   Unit    type   
     0     Temperature        55      5        100       -27     C       Voltage
     1     Input_-48V_0       75      45       75        0       volt    Voltage
     2     -                  127     -128     127       -128    -       Voltage
     3     -                  127     -128     127       -128    -       Voltage
  ----------------------------------------------------------------------------  
  DigitalID Name        Available Level|DigitalID Name        Available Level   
     0     Wiring                1     |   1     Door0                 0        
     2     -                     1     |   3     -                     1        
     4     -                     1     |   5     -                     1        
     6     -                     1     |   7     -                     1        
     8     -                     1     |   9     -                     1        
  ----------------------------------------------------------------------------  

The results show that certain monitoring parameters, such as temperature, voltage, door
status, and MDF, have been configured automatically in the system. Other monitoring
parameters, however, need to be configured manually.

4.

Configure the analog parameters.

huawei(config-if-MiniESC-0)#

esc analog 0 alarm-upper-limit 50 alarm-lower-

limit 10

UA5000 Universal Access Unit
Environment Monitoring

5 ESCM Monitoring Solution

Issue 01 (2012-08-17)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

56

Summary of Contents for UA5000


















































































































































































































Reviews:

No comments

Related manuals for UA5000

ZyXEL Communications P-2602HWUDL-D Quick Start Manual preview
P-2602HWUDL-D
Brand: ZyXEL Communications Pages: 15
PRO-NETS WR861R User Manual preview
WR861R
Brand: PRO-NETS Pages: 72
ZyXEL Communications NWA1100-NH Quick Start Manual preview
NWA1100-NH
Brand: ZyXEL Communications Pages: 2
Digi TransPort WR44RR Installation Manual preview
TransPort WR44RR
Brand: Digi Pages: 24
D-Link DWL-1000AP+ Manual preview
DWL-1000AP+
Brand: D-Link Pages: 40
D-Link DAP-600P Quick Installation Manual preview
DAP-600P
Brand: D-Link Pages: 46
D-Link DAP-3310 Quick Installation Manual preview
DAP-3310
Brand: D-Link Pages: 24
D-Link DWL-3200A Command Line Interface Reference Manual preview
DWL-3200A
Brand: D-Link Pages: 23
D-Link DWL-3140AP - Web Smart PoE Thin Access Point Quick Install Manual preview
DWL-3140AP - Web Smart PoE Thin Access Point
Brand: D-Link Pages: 72
D-Link DAP-400P Quick Installation Manual preview
DAP-400P
Brand: D-Link Pages: 46
D-Link DWL-2130AP - xStack - Wireless Access Point Quick Installation Manual preview
DWL-2130AP - xStack - Wireless Access Point
Brand: D-Link Pages: 12
D-Link DBA-1210P Quick Installation Manual preview
DBA-1210P
Brand: D-Link Pages: 8
D-Link DWL-2230AP - xStack - Wireless Access Point Quick Installation Manual preview
DWL-2230AP - xStack - Wireless Access Point
Brand: D-Link Pages: 12
D-Link DWL-2100AP - AirPlus Xtreme G Specifications preview
DWL-2100AP - AirPlus Xtreme G
Brand: D-Link Pages: 2
D-Link DWL-1000AP+ Quick Installation Manual preview
DWL-1000AP+
Brand: D-Link Pages: 8
D-Link DI-713 Quick Installation Manual preview
DI-713
Brand: D-Link Pages: 5
D-Link DWL-3200AP - AirPremier - Wireless Access Point Product Manual preview
DWL-3200AP - AirPremier - Wireless Access Point
Brand: D-Link Pages: 113
D-Link DAP-3666 Quick Installation Manual preview
DAP-3666
Brand: D-Link Pages: 16

Brands by name

Popular brands

Load more brands